44 MCQs for MDCAT Physics. The quiz above checks one question at a time. Every question, option, and saved explanation is on this page.
-
Q1.
The SI unit of electric current is
A) Coulomb
B) Ampere
C) Volt
D) Ohm
Answer: B
Electric current is defined as the rate at which electric charge flows through a cross-section of a conductor. In the International System of Units (SI), the standard unit for measuring this flow is the Ampere (symbol: A). One Ampere is equivalent to the flow of one Coulomb of charge per second. This can be represented by the formula:
\[ I = \frac{Q}{t} \]
where \( I \) is the current in Amperes, \( Q \) is the electric charge in Coulombs, and \( t \) is the time in seconds.
To clarify the other options provided:
1. Coulomb (A): This is the SI unit of electric charge, not current. It represents the quantity of electricity.
2. Volt (C): This is the SI unit of electric potential difference or electromotive force, which drives the current through a circuit.
3. Ohm (D): This is the SI unit of electrical resistance, which quantifies how much a material opposes the flow of electric current.
Because the question specifically asks for the unit of current, the Ampere is the correct choice.
The Ampere is the fundamental SI unit used to measure the intensity of electric current in a conductor.
-
Q2.
The current density J is related to current I by
A) $I=J\cdot A$
B) $I=J/A$
C) $I=JA$
D) $I=J+A$
Answer: C
Current density, represented by the symbol \( J \), is a measure of the intensity of an electric current. It is defined as the amount of electric current (\( I \)) flowing through a unit cross-sectional area (\( A \)) that is perpendicular to the direction of the flow.
The fundamental formula for current density is:
\[ J = \frac{I}{A} \]
To find the relationship for current (\( I \)), we can rearrange this equation by multiplying both sides by the area (\( A \)). This gives us:
\[ I = J \times A \]
or simply:
\[ I = JA \]
In this relationship:
- \( I \) is the electric current, measured in Amperes (A).
- \( J \) is the current density, measured in Amperes per square meter (\( A/m^{2} \)).
- \( A \) is the cross-sectional area, measured in square meters (\( m^{2} \)).
While current density is technically a vector quantity and current is the flux of that vector through a surface, in basic algebraic terms for a uniform current flowing perpendicular to a surface, the magnitude of the current is the product of the current density and the area. Therefore, Option C is the correct mathematical representation.
Current is the product of current density and the cross-sectional area through which the charges flow.
-
Q3.
The SI unit of current density is
A) A/m
B) A/m$^{2}$
C) A$^{2}$/m
D) A/m$^{3}$
Answer: B
Current density, often represented by the symbol J, is defined as the amount of electric current flowing through a unit cross-sectional area of a conductor. To determine its SI unit, we can look at its mathematical definition:
\[ J = \frac{I}{A} \]
In this equation:
1. I represents the electric current, which is measured in Amperes (A) in the International System of Units (SI).
2. A represents the cross-sectional area, which is measured in square meters (\( m^{2} \)) in the SI system.
By substituting these units into the formula, we find that the unit of current density is the ratio of current to area:
\[ \text{Unit of } J = \frac{\text{Ampere}}{\text{meter}^{2}} = \text{A/m}^{2} \]
Other options like A/m or A/m\(^{3}\) are incorrect because they represent current per unit length or current per unit volume, respectively, which do not define current density. Therefore, the standard unit is Amperes per square meter.
The SI unit of current density is \( \text{A/m}^{2} \) because it represents the distribution of electric current over a specific cross-sectional area.
-
Q4.
Ohm's law states that
A) V ? I
B) V = IR
C) Both A and B
D) Neither A nor B
Answer: C
Ohm's law describes the fundamental relationship between voltage, current, and resistance in an electrical circuit.
Reasoning for Option A:
The core principle of Ohm's law is that the potential difference (voltage) across a conductor is directly proportional to the electric current flowing through it, provided that physical conditions such as temperature remain constant. This proportionality is written as \( V \propto I \).
Reasoning for Option B:
To transform this proportionality into a usable mathematical equation, we introduce a constant of proportionality known as resistance (\( R \)). This results in the well-known formula \( V = IR \), which allows for the calculation of any of the three variables if the other two are known.
Conclusion:
Since Option A represents the conceptual proportionality of the law and Option B represents the standard algebraic expression of the law, both are correct representations. Consequently, Option C is the most accurate choice.
Ohm's law defines the direct proportionality between voltage and current, which is mathematically expressed through the equation \( V = IR \).
-
Q5.
The SI unit of resistance is
A) Ohm
B) Volt/Ampere
C) Both A and B
D) Neither A nor B
Answer: C
To determine the SI unit of resistance, we refer to Ohm's Law, which defines the relationship between voltage, current, and resistance. The law is expressed by the following formula:
\[ V = I \times R \]
In this equation, V represents the potential difference (measured in Volts), I represents the electric current (measured in Amperes), and R represents the electrical resistance.
By rearranging this formula to isolate resistance, we obtain:
\[ R = \frac{V}{I} \]
From this mathematical expression, we can see that the unit of resistance is equivalent to the unit of voltage divided by the unit of current. This gives us the unit Volt/Ampere.
In the International System of Units (SI), this derived unit is specifically named the Ohm (symbolized by the Greek letter \( \Omega \)) in honor of the German physicist Georg Simon Ohm. Since both Ohm and Volt/Ampere describe the same physical quantity and are dimensionally identical, both options A and B are correct.
Therefore, resistance is measured in Ohms, which is fundamentally defined as one Volt per Ampere.
-
Q6.
The SI unit of resistivity is
A) Ohm meter
B) Ohm/meter
C) Ohm/meter$^{2}$
D) Ohm meter$^{2}$
Answer: A
To determine the SI unit of resistivity, we begin with the fundamental formula for electrical resistance:
\[ R = \rho \frac{L}{A} \]
In this equation:
\( R \) is the resistance of the conductor, measured in Ohms (\( \Omega \)).
\( \rho \) (rho) is the resistivity of the material.
\( L \) is the length of the conductor, measured in meters (\( m \)).
\( A \) is the cross-sectional area of the conductor, measured in square meters (\( m^{2} \)).
To find the unit of resistivity, we rearrange the formula to solve for \( \rho \):
\[ \rho = \frac{R \cdot A}{L} \]
Next, we substitute the standard SI units for resistance, area, and length into the rearranged equation:
\[ \text{Unit of } \rho = \frac{\text{Ohm} \cdot m^{2}}{m} \]
By simplifying the expression, one meter (\( m \)) in the denominator cancels out one meter in the numerator:
\[ \text{Unit of } \rho = \text{Ohm} \cdot m \]
This result shows that the SI unit of resistivity is the Ohm meter. Options B, C, and D are incorrect because they involve incorrect mathematical relationships between the units of resistance and geometry.
The SI unit of resistivity is the Ohm meter because it represents the resistance of a material per unit length and cross-sectional area.
-
Q7.
The resistivity of a material depends on
A) Length
B) Area
C) Nature of material
D) All of these
Answer: C
To understand why resistivity depends only on the nature of the material, it is important to distinguish between resistance and resistivity.
The resistance \( R \) of a conductor is determined by its physical dimensions and the material it is made of, according to the formula:
\[ R = \rho \frac{L}{A} \]
In this equation:
1. \( R \) is the resistance.
2. \( L \) is the length of the conductor.
3. \( A \) is the cross-sectional area.
4. \( \rho \) (rho) is the resistivity.
While the resistance \( R \) changes if you change the length or the thickness of a wire, the resistivity \( \rho \) is an intrinsic property of the material itself. This means that resistivity does not depend on the shape or size of the object. For example, a small copper penny and a long copper pipe have different resistances, but they have the exact same resistivity because the nature of the material (copper) is the same in both cases.
Resistivity is determined by the internal atomic structure of the substance and how easily electrons can move through it. The only other factor that typically affects resistivity is temperature, but among the physical dimensions listed in the options, it remains independent of length and area.
Therefore, length and area affect the total resistance, but only the type of substance determines the resistivity.
In summary, resistivity is a characteristic property of a substance that depends solely on the nature of the material and its temperature.
-
Q8.
The resistance of a conductor depends on
A) Length
B) Area
C) Temperature
D) All of these
Answer: D
The resistance of a conductor is influenced by several physical characteristics and environmental factors.
1. Length of the Conductor: The resistance \( R \) is directly proportional to the length \( L \) of the conductor. As the length increases, electrons must travel a longer distance and encounter more collisions with the atoms of the material, which increases the total resistance.
2. Cross-sectional Area: Resistance is inversely proportional to the cross-sectional area \( A \) of the conductor. A larger area provides more space for electrons to move through, reducing the frequency of collisions and thus lowering the resistance. This is why thicker wires generally have less resistance than thinner ones of the same material and length.
3. Temperature: For most metallic conductors, resistance increases as the temperature rises. Higher temperatures cause the atoms in the lattice to vibrate more intensely, which creates more frequent collisions for the drifting electrons, hindering their flow.
The relationship between these factors (excluding temperature, which affects the resistivity \( \rho \)) is mathematically represented by the formula:
\[ R = \rho \frac{L}{A} \]
In this equation, \( R \) is the resistance, \( \rho \) is the resistivity (which is dependent on the material and temperature), \( L \) is the length, and \( A \) is the cross-sectional area.
Since length, area, and temperature all play a significant role in determining how much a conductor opposes the flow of electric current, the correct answer is All of these.
In summary, the resistance of a conductor is a property determined by its physical dimensions, the nature of its material, and its thermal state.
-
Q9.
The temperature coefficient of resistance is positive for
A) Metals
B) Semiconductors
C) Insulators
D) All of these
Answer: A
The temperature coefficient of resistance, often denoted by the Greek letter \(\alpha\), is a measure of how the electrical resistance of a material changes in response to a change in temperature.
In Metals (conductors), the resistance increases as the temperature rises. This occurs because, as the metal heats up, the atoms within the crystal lattice vibrate more intensely. These increased vibrations lead to more frequent collisions between the flowing free electrons and the metal ions. These collisions hinder the movement of electrons, thereby increasing the electrical resistance. Because the resistance and temperature move in the same direction, metals are said to have a positive temperature coefficient of resistance.
On the other hand, for Semiconductors and Insulators, the behavior is different. As the temperature increases, the thermal energy provides enough power to break covalent bonds, releasing more charge carriers (electrons and holes). This increase in the concentration of charge carriers significantly outweighs the effect of lattice vibrations, causing the resistance to decrease as temperature increases. Therefore, these materials have a negative temperature coefficient of resistance.
The mathematical relationship is generally expressed as:
\[ R = R_0 [1 + \alpha(T - T_0)] \]
Where \(R\) is the resistance at temperature \(T\), \(R_0\) is the resistance at a reference temperature \(T_0\), and \(\alpha\) is the temperature coefficient. For metals, \(\alpha\) is a positive value, indicating that resistance and temperature are directly proportional.
In summary, metals exhibit a positive temperature coefficient of resistance because their resistance increases with an increase in temperature.
-
Q10.
The temperature coefficient of resistance is negative for
A) Metals
B) Semiconductors
C) Insulators
D) All of these
Answer: B
-
Q11.
If two resistors of resistance R each are connected in series, the equivalent resistance is
A) R
B) 2R
C) R/2
D) 4R
Answer: B
When resistors are connected in series, they are arranged end-to-end in a single path. This configuration means that the same electric current must flow through each resistor sequentially.
The fundamental principle for calculating the total or equivalent resistance (represented as \( R_{eq} \)) in a series circuit is to find the algebraic sum of all individual resistances. The general formula is expressed as:
\[ R_{eq} = R_{1} + R_{2} + R_{3} + ... + R_{n} \]
In this specific problem, we are provided with two resistors, and both have a resistance value of R. Applying the values to the formula:
\( R_{1} = R \)
\( R_{2} = R \)
By adding them together, we get:
\[ R_{eq} = R + R \]
\[ R_{eq} = 2R \]
This demonstrates that the total resistance increases as more resistors are added in a series arrangement. Since the sum of the two resistances is \( 2R \), option B is the correct choice.
In a series connection, the equivalent resistance is always the sum of the individual resistances.
-
Q12.
If two resistors of resistance R each are connected in parallel, the equivalent resistance is
A) R
B) 2R
C) R/2
D) 4R
Answer: C
-
Q13.
Kirchhoff's first law is based on conservation of
A) Charge
B) Energy
C) Momentum
D) Mass
Answer: A
-
Q14.
Kirchhoff's second law is based on conservation of
A) Charge
B) Energy
C) Momentum
D) Mass
Answer: B
-
Q15.
The SI unit of electrical power is
A) Watt
B) Joule/second
C) Both A and B
D) Neither A nor B
Answer: C
-
Q16.
The power dissipated in a resistor is
A) $I^{2}R$
B) $V^{2}/R$
C) VI
D) All of these
Answer: D
-
Q17.
The energy dissipated in a resistor in time t is
A) $I^{2}Rt$
B) $V^{2}t/R$
C) V I t
D) All of these
Answer: D
-
Q18.
The SI unit of electrical energy is
A) Joule
B) Kilowatt-hour
C) Both A and B
D) Neither A nor B
Answer: C
-
Q19.
1 kilowatt-hour is equal to
A) $3.6\times10^{6} J$
B) $3.6\times10^{3} J$
C) $3.6\times10^{-3} J$
D) $3.6\times10^{-6} J$
Answer: A
-
Q20.
The emf of a cell is defined as
A) Work done per unit charge
B) Energy per unit charge
C) Both A and B
D) Neither A nor B
Answer: C
-
Q21.
The terminal voltage of a cell is equal to emf when
A) No current is drawn
B) Current is drawn
C) The cell is short-circuited
D) The cell is open-circuited
Answer: D
-
Q22.
The internal resistance of a cell can be determined by
A) Potentiometer
B) Meter bridge
C) Both A and B
D) Neither A nor B
Answer: C
-
Q23.
The potentiometer is used to
A) Measure emf
B) Compare emfs
C) Measure internal resistance
D) All of these
Answer: D
-
Q24.
The Wheatstone bridge is used to measure
A) Resistance
B) Current
C) Voltage
D) Power
Answer: A
-
Q25.
The meter bridge is based on the principle of
A) Potentiometer
B) Wheatstone bridge
C) Ohm's law
D) Kirchhoff's law
Answer: B
-
Q26.
The sensitivity of a potentiometer can be increased by
A) Increasing the length of the wire
B) Decreasing the potential gradient
C) Both A and B
D) Neither A nor B
Answer: C
The sensitivity of a potentiometer refers to its ability to detect and measure very small potential differences. A potentiometer is considered more sensitive if it shows a significant change in the balance length for a very small change in the potential being measured.
The sensitivity is inversely proportional to the potential gradient (\( k \)). The potential gradient is defined as the potential drop per unit length of the potentiometer wire, expressed by the formula:
\[ k = \frac{V}{L} \]
where \( V \) is the potential difference across the wire and \( L \) is the total length of the wire.
To increase the sensitivity, we need to make the potential gradient (\( k \)) as small as possible. This can be achieved in two primary ways:
1. Increasing the length of the wire (Option A): By increasing the length \( L \) of the potentiometer wire while keeping the potential difference \( V \) constant, the value of \( k \) decreases. A smaller potential gradient means that the potential drops more slowly over the length of the wire, allowing for more precise readings.
2. Decreasing the potential gradient (Option B): This is the direct requirement for increasing sensitivity. Apart from increasing the length, the potential gradient can also be decreased by reducing the current flowing through the potentiometer wire (for example, by adding a series resistance in the primary circuit).
Since both increasing the length of the wire and decreasing the potential gradient result in higher sensitivity, both statements A and B are correct.
Summary: The sensitivity of a potentiometer is enhanced by reducing the potential gradient, which can be effectively done by increasing the length of the potentiometer wire.
-
Q27.
The potential gradient along the potentiometer wire can be decreased by
A) Increasing the length of the wire
B) Decreasing the current in the wire
C) Both A and B
D) Neither A nor B
Answer: C
To understand how to decrease the potential gradient, we must first look at its fundamental definition. The potential gradient, often denoted by \( k \), is defined as the potential drop per unit length along the potentiometer wire. It is mathematically expressed as:
\[ k = \frac{V}{L} \]
where \( V \) is the potential difference across the wire and \( L \) is the total length of the wire.
1. Increasing the length of the wire (Option A):
According to the formula \( k = V/L \), the potential gradient is inversely proportional to the length of the wire. If the length \( L \) is increased while the potential difference \( V \) is maintained, the value of \( k \) will decrease. In a practical circuit, increasing the length of the wire increases its total resistance; if the driving voltage remains the same, this leads to a smaller potential drop per unit of length.
2. Decreasing the current in the wire (Option B):
We can also express the potential gradient in terms of current using Ohm's Law (\( V = IR \)). Since the resistance of the wire is \( R = \rho \frac{L}{A} \) (where \( \rho \) is resistivity and \( A \) is the cross-sectional area), the potential gradient becomes:
\[ k = \frac{IR}{L} = \frac{I (\rho \frac{L}{A})}{L} = \frac{I \rho}{A} \]
This formula shows that the potential gradient is directly proportional to the current \( I \) flowing through the wire. Therefore, if the current is decreased (for example, by increasing the resistance in the primary circuit using a rheostat), the potential gradient \( k \) will also decrease.
Conclusion:
Since both increasing the length of the wire and decreasing the current flowing through it effectively reduce the potential drop per unit length, both options A and B are valid methods to decrease the potential gradient.
In summary, the potential gradient is decreased by increasing the wire length or decreasing the current, which ultimately increases the sensitivity of the potentiometer.
-
Q28.
The thermistor is a device whose resistance
A) Increases with temperature
B) Decreases with temperature
C) Remains constant with temperature
D) First increases then decreases
Answer: B
A thermistor, a portmanteau of thermal and resistor, is a type of semiconductor device whose electrical resistance is highly sensitive to changes in temperature. Unlike standard metallic conductors where resistance typically increases with temperature due to increased atomic vibrations, most common thermistors are classified as Negative Temperature Coefficient (NTC) devices.
In an NTC thermistor, the material is engineered such that as the temperature rises, the thermal energy allows more electrons to break free from their atomic bonds. This process increases the concentration of charge carriers (electrons and holes) available for conduction. According to the principles of physics, an increase in the number of charge carriers leads to higher conductivity, which inversely results in a decrease in electrical resistance.
The mathematical relationship between resistance and temperature for a thermistor can often be approximated by the following formula:
\[ R = R_0 \cdot e^{\beta (\frac{1}{T} - \frac{1}{T_0})} \]
In this equation, \( R \) is the resistance at temperature \( T \), and \( \beta \) is a constant specific to the material. As the absolute temperature \( T \) increases, the exponent decreases, leading to a lower value for \( R \). This property makes thermistors ideal for use in temperature sensors, current limiters, and overcurrent protectors.
In summary, the resistance of a standard thermistor decreases as the temperature increases due to the release of additional charge carriers within the semiconductor material.
-
Q29.
The superconductor is a material whose resistance
A) Becomes zero below a critical temperature
B) Becomes infinite below a critical temperature
C) Remains constant below a critical temperature
D) Increases below a critical temperature
Answer: A
-
Q30.
The drift velocity of electrons in a conductor is of the order of
A) $10^{-3} m/s$
B) $10^{-5} m/s$
C) $10^{-7} m/s$
D) $10^{-9} m/s$
Answer: C
The reasoning for the drift velocity of electrons in a conductor is based on the microscopic behavior of charge carriers under the influence of an electric field.
In a metallic conductor, free electrons are in a state of continuous random motion due to thermal energy. This thermal velocity is quite high, typically reaching speeds of \( 10^5 \) to \( 10^6 \) m/s. However, because this motion is completely random, the average velocity in any specific direction is zero, meaning no net current flows.
When an external electric field is applied (by connecting a battery), the electrons experience an electric force that pushes them toward the positive terminal. Despite this force, the electrons do not accelerate indefinitely. Instead, they undergo frequent collisions with the relatively stationary positive ions of the metal lattice.
These collisions constantly interrupt the path of the electrons, causing them to lose the kinetic energy gained from the field. The result is a very slow, net directional movement known as drift velocity (\( v_d \)).
The relationship between the current (\( I \)) flowing through a conductor and the drift velocity is expressed by the formula:
\[ I = nAev_d \]
Where:
\( n \) is the number of free electrons per unit volume (electron density),
\( A \) is the cross-sectional area of the conductor,
\( e \) is the charge of an electron (\( \approx 1.6 \times 10^{-19} \) C), and
\( v_d \) is the drift velocity.
In typical metallic conductors like copper, the value of \( n \) is extremely large (approximately \( 10^{28} \) to \( 10^{29} \) electrons per cubic meter). Because the electron density is so high, even a substantial electric current requires only a very small drift velocity. While the exact value depends on the specific material and current density, the typical order of magnitude for drift velocity is very small, often falling within the range of \( 10^{-4} \) m/s to \( 10^{-7} \) m/s. Based on the options provided, the order of magnitude is identified as \( 10^{-7} \) m/s.
Summary: Drift velocity is the very slow average speed at which electrons travel through a conductor due to an electric field, limited by frequent collisions with the metal's atomic lattice.
-
Q31.
The mobility of charge carriers is defined as
A) Drift velocity per unit electric field
B) Electric field per unit drift velocity
C) Charge per unit mass
D) Mass per unit charge
Answer: A
-
Q32.
The SI unit of mobility is
A) m$^{2}$/V s
B) V s/m$^{2}$
C) m/V s
D) V s/m
Answer: A
-
Q33.
The current in a conductor is due to
A) Drift of electrons
B) Drift of protons
C) Drift of ions
D) All of these
Answer: A
-
Q34.
The number density of free electrons in a metal is of the order of
A) $10^{28} m^{-3}$
B) $10^{24} m^{-3}$
C) $10^{20} m^{-3}$
D) $10^{16} m^{-3}$
Answer: A
-
Q35.
The resistivity of a conductor increases with temperature because
A) Number density of free electrons decreases
B) Relaxation time decreases
C) Both A and B
D) Neither A nor B
Answer: B
-
Q36.
The resistivity of a semiconductor decreases with temperature because
A) Number density of charge carriers increases
B) Relaxation time increases
C) Both A and B
D) Neither A nor B
Answer: A
The resistivity of a material is mathematically expressed by the formula:
\[ \rho = \frac{m}{n e^2 \tau} \]
In this formula:
- \( m \) represents the mass of the charge carrier.
- \( e \) represents the elementary charge.
- \( n \) represents the number density of charge carriers (the number of free electrons or holes per unit volume).
- \( \tau \) represents the relaxation time (the average time between successive collisions of charge carriers).
When the temperature of a semiconductor increases, two competing effects occur:
1. Increase in Number Density (\( n \)): Thermal energy breaks covalent bonds within the semiconductor lattice, releasing a large number of electrons and holes. This causes the number density of charge carriers to increase exponentially with temperature.
2. Decrease in Relaxation Time (\( \tau \)): Higher temperatures cause the ions in the lattice to vibrate more violently, leading to more frequent collisions with the charge carriers. This reduces the relaxation time.
In semiconductors, the increase in the number density (\( n \)) is much more significant and dominant than the decrease in the relaxation time (\( \tau \)). Because the resistivity \( \rho \) is inversely proportional to \( n \), the substantial increase in charge carriers leads to a net decrease in the overall resistivity of the material.
This behavior is the reason why semiconductors are said to have a negative temperature coefficient of resistance.
Summary: The resistivity of a semiconductor decreases with temperature primarily because the number density of charge carriers increases significantly, overcoming the effect of decreased relaxation time.
-
Q37.
The color code for a resistor of resistance 1 kO with 5% tolerance is
A) Brown, black, red, gold
B) Brown, black, orange, gold
C) Brown, black, red, silver
D) Brown, black, orange, silver
Answer: A
To determine the color code for a resistor, we follow the standard electronic color code chart for a four-band resistor. In this system, the first two bands represent the significant digits, the third band represents the multiplier, and the fourth band represents the tolerance.
The resistance value given is \( 1 \text{ k}\Omega \), which is equivalent to \( 1000 \ \Omega \). To find the color code, we break this number down into its significant digits and its multiplier: \( 10 \times 10^2 \ \Omega \).
Step 1: First Digit
The first digit is 1. In the resistor color code, the number 1 corresponds to the color Brown.
Step 2: Second Digit
The second digit is 0. In the resistor color code, the number 0 corresponds to the color Black.
Step 3: Multiplier
The multiplier is \( 10^2 \) (since \( 10 \times 100 = 1000 \)). The exponent 2 corresponds to the color Red.
Step 4: Tolerance
The tolerance is given as 5%. In the color code system, a 5% tolerance is represented by the color Gold. If the tolerance were 10%, the color would be Silver.
By putting these together, the sequence of colors is Brown (1), Black (0), Red (\( 10^2 \)), and Gold (\( \pm 5\% \)).
This confirms that Option A is the correct choice. Option B is incorrect because Orange represents a multiplier of \( 10^3 \), which would result in a \( 10 \text{ k}\Omega \) resistor. Options C and D are incorrect because Silver represents a 10% tolerance.
The color code for a \( 1 \text{ k}\Omega \) resistor with 5% tolerance is Brown, Black, Red, and Gold.
-
Q38.
The color code for a resistor of resistance 10 MO with 10% tolerance is
A) Brown, black, blue, silver
B) Brown, black, green, silver
C) Brown, black, blue, gold
D) Brown, black, green, gold
Answer: A
To determine the color code for a resistor, we follow the standard electronic color code system, which typically uses four bands to represent the resistance value and tolerance.
The given resistance is 10 M\(\Omega\). First, we convert this value into ohms:
\[ 10 \text{ M}\Omega = 10,000,000 \Omega = 10 \times 10^6 \Omega \]
Now, we break down the value into its significant digits, multiplier, and tolerance:
1. First Digit: The first significant digit is 1. In the resistor color code chart, the number 1 corresponds to the color Brown.
2. Second Digit: The second significant digit is 0. In the color code chart, the number 0 corresponds to the color Black.
3. Multiplier: The multiplier is the power of ten that the digits are multiplied by. Here, the multiplier is \( 10^6 \). The color representing a multiplier of \( 10^6 \) is Blue.
4. Tolerance: The tolerance indicates the precision of the resistor. The question specifies a tolerance of 10%. The color code for a 10% tolerance is Silver. (Note: Gold represents 5% and no band represents 20%).
By combining these colors in order, we get the sequence: Brown, Black, Blue, Silver.
This matches Option A, confirming that the first two bands represent the digits 1 and 0, the third band represents the mega (\( 10^6 \)) multiplier, and the fourth band represents the 10% tolerance.
In summary, the color code for a 10 M\(\Omega\) resistor with 10% tolerance is Brown, Black, Blue, and Silver.
-
Q39.
The value of resistance using color code: yellow, violet, orange, gold is
A) 47 kO ± 5%
B) 47 kO ± 10%
C) 4.7 kO ± 5%
D) 4.7 kO ± 10%
Answer: A
-
Q40.
The value of resistance using color code: red, red, red, silver is
A) 2.2 kO ± 10%
B) 22 kO ± 10%
C) 220 O ± 10%
D) 2.2 kO ± 5%
Answer: A
-
Q41.
The instrument used to measure potential difference is
A) Voltmeter
B) Ammeter
C) Galvanometer
D) Potentiometer
Answer: A
-
Q42.
The instrument used to measure current is
A) Voltmeter
B) Ammeter
C) Galvanometer
D) Potentiometer
Answer: B
-
Q43.
A galvanometer can be converted into an ammeter by connecting
A) A low resistance in parallel
B) A high resistance in parallel
C) A low resistance in series
D) A high resistance in series
Answer: A
-
Q44.
A galvanometer can be converted into a voltmeter by connecting
A) A low resistance in parallel
B) A high resistance in parallel
C) A low resistance in series
D) A high resistance in series
Answer: D