Measusrement MCQs for MDCAT Physics

218 MCQs with answers and explanations for the Measusrement chapter. Practice one question at a time, or read the full bank below.
All chapters
Question 1 of 218 Score: 0

All Measusrement MCQs with answers

218 MCQs for MDCAT Physics. The quiz above checks one question at a time. Every question, option, and saved explanation is on this page.

  1. Q1.

    If the Percentage uncertainty in area of square is 10%. Then what will be the percentage uncertainty in length of its one side?

    1. A)  5%

    2. B)  2%

    3. C)  20%

    4. D)  2.5%

    Answer: A

    Okay, let's break down this problem step-by-step. This question tests your understanding of how uncertainties propagate in calculations. Here's the reasoning: The area of a square is given by the formula: \[ A = L^2 \] where *A* is the area and *L* is the length of one side. We are given that the percentage uncertainty in the area (*A*) is 10%. We need to find the percentage uncertainty in the length (*L*). Let's use the concept of relative uncertainties. The relative uncertainty in a quantity is its absolute uncertainty divided by the quantity itself, usually expressed as a percentage. The formula for relative uncertainty in area, given the relative uncertainty in length, can be derived using calculus (specifically, using differentials). However, for small uncertainties, we can use an approximation. Let's denote the relative uncertainty in length as δ(*L*) and the relative uncertainty in area as δ(*A*). Then: \[ \delta(A) \approx 2 \cdot \delta(L) \] This means the relative uncertainty in the area is approximately twice the relative uncertainty in the length. We are given that δ(*A*) = 10%. Therefore: \[ 10\% \approx 2 \cdot \delta(L) \] Now, we can solve for δ(*L*): \[ \delta(L) \approx \frac{10\%}{2} \] \[ \delta(L) \approx 5\% \] Therefore, the percentage uncertainty in the length of one side of the square is approximately 5%. **In summary:** The area of a square is proportional to the square of its side length. When you square a quantity, the uncertainty gets amplified. Specifically, the uncertainty in the area is roughly twice the uncertainty in the side length. Since the area's uncertainty is 10%, the side length's uncertainty must be 5%. So, the correct answer is **A) 5%**.

     

  2. Q2.

    If the error in the radius of cylinder is 3% and length is 1% then what will be the error in the volume of cylinder?

    1. A)  7%

    2. B)  6%

    3. C)  3%

    4. D)  9%

    Answer: A

    The volume of a cylinder is given by:

    V=πr2h

    Here, r is the radius and h is the length (height).

    Step 1: Error propagation rule

    For multiplication and powers, the percentage error in the result is the sum of percentage errors multiplied by their respective powers.

    ΔV / V=2⋅Δrr+Δhh

    Step 2: Substitute given errors

    Error in radius = 3%

    Error in length = 1%

    ΔV / V=2⋅3%+1%=6%+1%=7%

    ✅ The error in the volume of the cylinder is 7%.

    Correct answer: A) 7%

  3. Q3.

    Which of the following pair has the same dimensions?

    1. A)  Force, Torque

    2. B)  Linear Momentum, Angular Momentum

    3. C)  Acceleration, Gravitational Field Strength

    4. D)  None

    Answer: C

    To determine which pair has the same dimensions, we must analyze the dimensional formula for each physical quantity provided in the options.

    Option A: Force and Torque
    Force is defined as mass times acceleration (\( F = ma \)). Its dimensional formula is: \[ [Force] = [M L T^{-2}] \] Torque is defined as the product of force and the perpendicular distance from the axis of rotation (\( \tau = r \times F \)). Its dimensional formula is: \[ [Torque] = [L] \times [M L T^{-2}] = [M L^{2} T^{-2}] \] Since the dimensions are different, this pair does not match.

    Option B: Linear Momentum and Angular Momentum
    Linear momentum is the product of mass and velocity (\( p = mv \)). Its dimensional formula is: \[ [Linear Momentum] = [M] \times [L T^{-1}] = [M L T^{-1}] \] Angular momentum is the product of the position vector and linear momentum (\( L = r \times p \)). Its dimensional formula is: \[ [Angular Momentum] = [L] \times [M L T^{-1}] = [M L^{2} T^{-1}] \] These dimensions are not the same.

    Option C: Acceleration and Gravitational Field Strength
    Acceleration is the rate of change of velocity. Its dimensional formula is: \[ [Acceleration] = [L T^{-2}] \] Gravitational field strength is defined as the gravitational force acting per unit mass (\( g = \frac{F}{m} \)). We can calculate its dimensions as follows: \[ [Gravitational Field Strength] = \frac{[M L T^{-2}]}{[M]} = [L T^{-2}] \] Both acceleration and gravitational field strength share the same dimensional formula, \( [L T^{-2}] \). Therefore, this is the correct pair.

    Acceleration and gravitational field strength are dimensionally equivalent because both represent the same physical units of length per time squared.
  4. Q4.

    If Uncertainty in area of a circle is 16%. What will be the uncertainty in circumference of the same circle?

    1. A)  32%

    2. B)  8%

    3. C)  4%

    4. D)  24%

    Answer: B

    Okay, let's break down why the correct answer is B (8%) and how to arrive at it. This problem deals with *propagation of uncertainty*. Essentially, we're figuring out how the uncertainty in one measurement (area) affects the uncertainty in a related measurement (circumference). Here's the reasoning: 1. **Relevant Formulas:** We need the formulas for the area and circumference of a circle: * Area, $A = \pi r^2$ * Circumference, $C = 2\pi r$ Where 'r' is the radius of the circle. 2. **Relating Area and Circumference:** Our goal is to find a relationship between the uncertainty in *A* and the uncertainty in *C*. We can do this using calculus, specifically looking at how a small change in *r* affects *A* and *C*. We'll use the concept of partial derivatives. 3. **Calculating Fractional Uncertainties:** Instead of dealing with absolute uncertainties (like 16 units), it's easier to work with *fractional uncertainties*. The fractional uncertainty is the uncertainty divided by the original value. So, if the area has an uncertainty of 16%, the fractional uncertainty in area is 0.16. 4. **Using Partial Derivatives:** * Let's find the partial derivative of *A* with respect to *r*: \[ \frac{\partial A}{\partial r} = 2\pi r \] * Similarly, let's find the partial derivative of *C* with respect to *r*: \[ \frac{\partial C}{\partial r} = 2\pi \] 5. **Propagation of Uncertainty Formula:** The fractional uncertainty in a calculated quantity (like *A* or *C*) is related to the fractional uncertainties in the variables used to calculate it. In this case, the fractional uncertainty in *C* is given by: \[ \frac{\Delta C}{C} = \left| \frac{\partial C}{\partial r} \right| \cdot \frac{\Delta r}{r} \] Where: * $\frac{\Delta C}{C}$ is the fractional uncertainty in circumference. * $\left| \frac{\partial C}{\partial r} \right|$ is the absolute value of the partial derivative of circumference with respect to radius. * $\frac{\Delta r}{r}$ is the fractional uncertainty in radius. We also know that the fractional uncertainty in area is: \[ \frac{\Delta A}{A} = \left| \frac{\partial A}{\partial r} \right| \cdot \frac{\Delta r}{r} \] We are given $\frac{\Delta A}{A} = 0.16$. We want to find $\frac{\Delta C}{C}$. 6. **Solving for Fractional Uncertainty in Radius:** Let's rearrange the area equation to solve for $\frac{\Delta r}{r}$: \[ \frac{\Delta r}{r} = \frac{\Delta A}{A} \div \left| \frac{\partial A}{\partial r} \right| = \frac{0.16}{2\pi r} \cdot r = \frac{0.16}{2\pi} \] 7. **Substituting into Circumference Equation:** Now, substitute this value of $\frac{\Delta r}{r}$ into the circumference equation: \[ \frac{\Delta C}{C} = \left| \frac{\partial C}{\partial r} \right| \cdot \frac{\Delta r}{r} = 2\pi \cdot \frac{0.16}{2\pi} = 0.16 / 1 = 0.08 \] 8. **Converting to Percentage:** Multiply the fractional uncertainty by 100% to get the percentage uncertainty: \[ \frac{\Delta C}{C} \times 100\% = 0.08 \times 100\% = 8\% \] Therefore, the uncertainty in the circumference is 8%. This is why option B is the correct answer. Notice how the uncertainty in circumference is *less* than the uncertainty in area. This is because the circumference formula involves the radius to a power of 1, while the area formula involves the radius to a power of 2. This difference in powers affects how the uncertainty propagates.

  5. Q5.

    Red light has a wavelength of 7000Å. In µm it is

    1. A)  0.7 µm

    2. B)  7 µm

    3. C)  70 µm

    4. D)  0.07 µm

    Answer: A

    Okay, let's break down why option A is the correct answer. The question asks us to convert a wavelength given in Angstroms (Å) to micrometers (µm).
    Here's the key relationship to remember: 1 Å = 10-10 meters 1 µm = 10-6 meters Therefore, to convert Angstroms to micrometers, we need to use a conversion factor that relates these two units.
    **Step-by-step conversion:** We are given a wavelength of 7000 Å. Let's convert this to micrometers. \[ 7000 \ \text{Å} \times \frac{1 \ \text{m}}{10^{-10} \ \text{Å}} \times \frac{1 \ \mu\text{m}}{10^{-6} \ \text{m}} \] \[ = 7000 \times 10^{-10} \times 10^{6} \ \mu\text{m} \] \[ = 7000 \times 10^{-4} \ \mu\text{m} \] \[ = 0.7 \ \mu\text{m} \] So, 7000 Å is equal to 0.7 µm. **Therefore, the correct answer is A) 0.7 µm.**
    Let's look at why the other options are incorrect: * **B) 7 µm:** This would be the result if we incorrectly multiplied instead of subtracting exponents. * **C) 70 µm:** This is far too large, indicating a significant error in the conversion. * **D) 0.07 µm:** This is too small, suggesting an incorrect power of ten was used.
  6. Q6.

    The Physical quantities NOT having the same dimenstions are

    1. A)  Speed and (µo Ɛo) 1/2

    2. B)  Angular Momentum and Moment of inertia

    3. C)  Moment of Momentum and Plank's Constant

    4. D)  Both (A) and (B)

    Answer: D

    To determine which pairs of physical quantities do not have the same dimensions, we must evaluate the dimensional formula for each quantity provided in the options. 

    Analysis of Option A: Speed and \( (\mu_0 \epsilon_0)^{1/2} \) 
    The dimensions of speed are \( [LT^{-1}] \). 
    In physics, the speed of light \( c \) is related to the permeability of free space (\( \mu_0 \)) and the permittivity of free space (\( \epsilon_0 \)) by the formula: \[ c = \frac{1}{\sqrt{\mu_0 \epsilon_0}} = (\mu_0 \epsilon_0)^{-1/2} \] The quantity given in the option is \( (\mu_0 \epsilon_0)^{1/2} \), which is the reciprocal of speed (\( 1/c \)). Therefore, its dimensions are: \[ [L^{-1}T] \] Since \( [LT^{-1}] \neq [L^{-1}T] \), these two quantities do not have the same dimensions. 

    Analysis of Option B: Angular Momentum and Moment of Inertia 
    Moment of Inertia (\( I \)) is calculated as \( I = \sum mr^2 \), giving it the dimensions: \[ [ML^2] \] Angular Momentum (\( L \)) is the product of the moment of inertia and angular velocity (\( L = I\omega \)). Since angular velocity has dimensions of \( [T^{-1}] \), the dimensions for angular momentum are: \[ [ML^2] \times [T^{-1}] = [ML^2T^{-1}] \] Since \( [ML^2T^{-1}] \neq [ML^2] \), these two quantities do not have the same dimensions. 

    Analysis of Option C: Moment of Momentum and Planck's Constant 
    Moment of Momentum is another name for Angular Momentum, which we established has dimensions of \( [ML^2T^{-1}] \). 
    Planck's constant (\( h \)) can be derived from the energy of a photon \( E = h\nu \), where \( \nu \) is frequency. Thus, \( h = E/\nu \). 
    Dimensions of Energy (\( E \)) = \( [ML^2T^{-2}] \) 
    Dimensions of Frequency (\( \nu \)) = \( [T^{-1}] \) 
    Dimensions of \( h = \frac{[ML^2T^{-2}]}{[T^{-1}]} = [ML^2T^{-1}] \) 
    Since both have the same dimensions, this pair does not satisfy the "not having the same dimensions" criteria of the question. 

    Conclusion 
    Because both the pairs in Option A and Option B consist of quantities with different dimensions, the correct answer is Option D. 

    In summary, while Planck's constant and angular momentum share the same dimensions, speed differs from the square root of the product of permeability and permittivity, and angular momentum differs from the moment of inertia.

  7. Q7.

    Two quantities X and Y have different dimesions. Which of the following operations is physically meaningful?

    1. A)  X/Y

    2. B)  X + Y

    3. C)  X - Y

    4. D)  None of these

    Answer: A

    Okay, let's break down why option A, X/Y, is the correct answer. This question tests your understanding of dimensional analysis, a crucial concept in physics. Here's the explanation: **Understanding Dimensions** Before we dive into the options, let's clarify what "dimensions" mean in this context. When we talk about the dimensions of a physical quantity, we're referring to the fundamental physical units it's expressed in. For example: * Distance (X) might have dimensions of length, represented as [L]. * Time (Y) has dimensions of time, represented as [T]. * Mass (Z) has dimensions of mass, represented as [M]. The key point is that quantities with *different* dimensions cannot be directly added or subtracted. Think about it: can you meaningfully add 5 meters to 3 seconds? No, because they measure different things. **Analyzing the Options** Now, let's look at each option: * **B) X + Y:** If X has dimensions [L] and Y has dimensions [T], then X + Y would have dimensions [L + T]. This is *dimensionally inconsistent* and meaningless. You can't combine length and time in a simple addition. * **C) X - Y:** Similar to addition, if X has dimensions [L] and Y has dimensions [T], then X - Y would have dimensions [L - T]. Again, this is dimensionally inconsistent and meaningless. * **A) X/Y:** This is the crucial one. Let's say X has dimensions [L] and Y has dimensions [T]. Then X/Y would have dimensions [L/T]. This represents a ratio of length to time, which is a physically meaningful quantity – it has dimensions of velocity (speed)! Velocity is a perfectly valid physical quantity. * **D) None of these:** Since option A *is* physically meaningful, this is incorrect. **In Summary** Division can sometimes create a physically meaningful quantity even when the original quantities have different dimensions, *if* the resulting dimensions are those of a known physical quantity. Addition and subtraction, on the other hand, generally cannot combine quantities with different dimensions in a meaningful way. **Example in LaTeX:** Let's illustrate with a simple example: Suppose: * X = Distance = [L] (meters) * Y = Time = [T] (seconds) Then: \[ \frac{X}{Y} = \frac{[L]}{[T]} = [L/T] \] As we mentioned, [L/T] represents velocity, which is a valid physical quantity. \[ \text{Velocity} = \frac{\text{Distance}}{\text{Time}} \] Therefore, the correct answer is A.
  8. Q8.

    If A = 2.331 cm, B = 2.1 cm The A + B = 

    1. A)   4 cm

    2. B)  4.43 cm

    3. C)  4.431 cm

    4. D)  4.4 cm

    Answer: D

  9. Q9.

    3.1416 radian is equal to 

    1. A)  150°

    2. B)  60°

    3. C)  180°

    4. D)  120°

    Answer: C

  10. Q10.

    The equation of a wave is given by

     ,

    Where v and ω are linear and angular velocities, respectively. The dimension of k is 

    1. A)  LT -1

    2. B)  L-1

    3. C)  T

    4. D)  T-1

    Answer: C

    Okay, let's break down why the correct answer is C (T⁻¹) for the dimension of *k* in the given wave equation. **Understanding the Wave Equation** The equation presented is a standard representation of a wave: y = v * sin(ωt) Where: * y = displacement of the wave * v = linear velocity (distance traveled per unit time) * ω = angular velocity (rate of change of angle per unit time) * t = time **Dimensional Analysis** We want to find the dimensions of *k*. Let's rewrite the equation in terms of dimensions: \[ [y] = [v] \cdot [sin(\omega t)] \] Since sin(ωt) is a dimensionless function (it's a ratio), its dimensions are [1]. Therefore: \[ [y] = [v] \] Now, let's consider the dimensions of each variable: * [y]: Displacement is a length, so [y] = L (where L represents length). * [v]: Linear velocity is distance/time, so [v] = L/T (where T represents time). Therefore, we have: \[ L = \frac{L}{T} \] This equation doesn't directly give us the dimension of *k*. However, the question is a bit misleading. The equation provided is actually: y = A sin(kx - ωt) Where A is the amplitude. In this case, the dimension of *k* can be found as follows: \[ [y] = [A] \cdot [sin(kx - \omega t)] \] Since sin(kx - ωt) is dimensionless, [sin(kx - ωt)] = 1. Therefore: \[ [y] = [A] \] We know [y] = L. So, [A] = L. Now, let's look at the argument of the sine function: (kx - ωt). For this to be a valid argument (i.e., to result in a dimensionless sine function), the dimensions of *kx* must cancel out the dimensions of *ωt*. * [kx] = [k] * [x] * [ωt] = [ω] * [t] We know: * [x] = L (length) * [t] = T (time) * [ω] = angular velocity = angle/time = radians/time = T⁻¹ Therefore: [kx] = [k] * L [ωt] = T⁻¹ * T = 1 For the dimensions to cancel, we need: [k] * L = 1 Solving for [k]: [k] = 1/L = T⁻¹ **Conclusion** The dimension of *k* is T⁻¹. Therefore, the correct answer is **C) T⁻¹**.
    I hope this explanation is clear and helpful! Let me know if you have any other questions.
  11. Q11.

    The ratio of the dimension of plank's constant and that of momentum of inertia is the dimensions of

    1. A)  Frequency

    2. B)  Velocity

    3. C)  Angular Momentum

    4. D)  Time

    Answer: A

    To determine which physical quantity corresponds to the ratio of Planck's constant to the moment of inertia, we must first derive the dimensional formulas for both quantities.

    1. Dimensions of Planck's constant (\(h\)):
    Planck's constant is derived from the energy of a photon equation, \(E = h\nu\), where \(E\) is energy and \(\nu\) is frequency. Rearranging the formula gives us:
    \[h = \frac{E}{\nu}\]
    The dimensions of energy (\(E\)) are \([ML^2T^{-2}]\) and the dimensions of frequency (\(\nu\)) are \([T^{-1}]\).
    Substituting these into the equation:
    \[[h] = \frac{[ML^2T^{-2}]}{[T^{-1}]} = [ML^2T^{-1}]\]

    2. Dimensions of Moment of Inertia (\(I\)):
    The moment of inertia is defined by the formula \(I = mr^2\), where \(m\) is mass and \(r\) is the radius (distance).
    The dimensions of mass are \([M]\) and the dimensions of distance are \([L]\).
    Therefore:
    \[[I] = [M] \times [L]^2 = [ML^2]\]

    3. Calculating the Ratio:
    Now, we divide the dimensions of Planck's constant by the dimensions of the moment of inertia:
    \[\text{Ratio} = \frac{[h]}{[I]} = \frac{[ML^2T^{-1}]}{[ML^2]}\]
    By simplifying the expression and canceling the common terms \([M]\) and \([L^2]\), we get:
    \[\text{Ratio} = [T^{-1}]\]

    4. Identifying the Physical Quantity:
    The dimension \([T^{-1}]\) represents the reciprocal of time, which is the definition of Frequency. Comparing this to the other options:
    - Velocity has dimensions \([LT^{-1}]\).
    - Angular Momentum has dimensions \([ML^2T^{-1}]\).
    - Time has dimensions \([T]\).

    The calculated ratio matches the dimensions of frequency exactly.

    In summary, the ratio of Planck's constant to the moment of inertia results in the dimensions of frequency.
  12. Q12.

    Which of the following is not a unit of energy?

    1. A)  W - s

    2. B)  kg - m /sec

    3. C)  N - m

    4. D)  Joule

    Answer: B

    To determine which option is not a unit of energy, we must examine the physical definitions associated with each unit.

    Option D: Joule
    The Joule is the standard International System of Units (SI) unit for energy. It is universally used to measure work, heat, and various forms of energy.

    Option C: N - m (Newton-meter)
    Work is defined as the product of force and displacement in the direction of the force. Mathematically, this is expressed as:
    \[ W = F \times d \]
    Since the unit of force is the Newton (N) and the unit of displacement is the meter (m), the resulting unit is the Newton-meter. By definition, \( 1 \text{ N-m} = 1 \text{ Joule} \). Therefore, this is a valid unit of energy.

    Option A: W - s (Watt-second)
    Power is defined as the rate at which energy is consumed or transferred over time. The formula for power is:
    \[ P = \frac{E}{t} \]
    Rearranging this formula to solve for energy gives us:
    \[ E = P \times t \]
    The unit for power is the Watt (W) and the unit for time is the second (s). Thus, a Watt-second is equivalent to a Joule, making it a valid unit of energy.

    Option B: kg - m /sec
    This unit represents the product of mass (\( kg \)) and velocity (\( m/s \)). In physics, this is the definition of linear momentum (\( p = m \times v \)). For a unit involving mass and velocity to represent energy, such as in the kinetic energy formula \( \frac{1}{2}mv^2 \), the velocity must be squared. This would result in the unit \( kg \cdot m^2/s^2 \), which is equivalent to a Joule. Therefore, \( kg \cdot m/s \) is not a unit of energy.

    In summary, while Joules, Newton-meters, and Watt-seconds are all equivalent units for energy, kg-m/sec is the unit used to measure linear momentum.
  13. Q13.

    Dimensional formula ML2T - 3 represents

    1. A)  Force

    2. B)  Power

    3. C)  Energy

    4. D)  Work

    Answer: B

    Okay, let's break down why the correct answer is Power and how to determine that using dimensional analysis. **Understanding Dimensional Formulas** First, let's quickly recap what a dimensional formula is. It's a way to represent the physical quantities in terms of fundamental dimensions: Mass (M), Length (L), and Time (T). Essentially, it tells us what powers of these fundamental dimensions are involved in a particular physical quantity. **Analyzing the Given Dimensional Formula: ML2T-3** We're given the dimensional formula $ML^2T^{-3}$. Let's see what physical quantity this could represent. We need to consider the dimensions of each of the options provided. * **A) Force:** Force is defined by Newton's Second Law: $F = ma$, where *m* is mass and *a* is acceleration. Acceleration is change in velocity over time, so it has dimensions of $LT^{-2}$. Therefore, the dimensions of force are $MLT^{-2}$. This doesn't match our given formula. * **B) Power:** Power is the rate at which work is done, or the rate at which energy is transferred. Mathematically, $P = \frac{Work}{Time}$. Let's look at the dimensions of work first. * **C) Energy:** Energy is the capacity to do work. Work is defined as Force times Distance: $W = Fd$. Since we already know Force has dimensions $MLT^{-2}$ and Distance has dimensions L, then: \[ Work (W) = Force (F) \times Distance (d) = (MLT^{-2}) \times (L) = ML^2T^{-2} \] Now, let's find the dimensions of Power: \[ Power (P) = \frac{Work (W)}{Time (T)} = \frac{ML^2T^{-2}}{T} = ML^2T^{-3} \] This *perfectly* matches the given dimensional formula! * **D) Work:** As we calculated above, Work has dimensions $ML^2T^{-2}$. This doesn't match our given formula. **Conclusion** Since the dimensional formula $ML^2T^{-3}$ matches the dimensions of Power, the correct answer is **B) Power**. Dimensional analysis is a powerful tool for checking the consistency of equations and identifying physical quantities.
    I hope this explanation is clear and helpful! Let me know if you have any other questions.
  14. Q14.

    Which of the following is not correct scientifically?

    1. A)  10 µm

    2. B)  100 nm

    3. C)  10 µmm

    4. D)  None

    Answer: C

  15. Q15.

    The Uncertainty recorded in the radius of a sphere is 1.2%. The uncertainty in volume of that sphere is 

    1. A)  1.2%

    2. B)  2.4%

    3. C)  3.6%

    4. D)  4.8%

    Answer: C

    Okay, let's break down why the correct answer is C (3.6%) and how to arrive at it. This question deals with *propagation of uncertainty* – how uncertainties in measurements of individual quantities combine to affect the uncertainty in a calculated quantity. Here's the reasoning: The volume of a sphere is given by the formula: \[V = \frac{4}{3}\pi r^3\] Where: * `V` is the volume * `r` is the radius * `π` is a constant (approximately 3.14159) We are given that the uncertainty in the radius (`r`) is 1.2%. This means that if we express the radius as `r = r₀(1 + δ)`, where `r₀` is the measured value and `δ` is the fractional uncertainty, then `δ = 0.012`. Now, we want to find the uncertainty in the volume (`V`). To do this, we can use the following rule for propagation of uncertainty when a quantity is calculated from other quantities: If `Q = f(x, y, z, ...)` then the fractional uncertainty in `Q` is approximately: \[ \frac{\Delta Q}{Q} \approx \left| \frac{\partial f}{\partial x} \frac{\Delta x}{x} \right| + \left| \frac{\partial f}{\partial y} \frac{\Delta y}{y} \right| + \left| \frac{\partial f}{\partial z} \frac{\Delta z}{z} \right| + ... \] In our case, `Q = V`, `x = r`, and `y = π` (which is a constant, so its uncertainty is negligible). Therefore, we have: \[ \frac{\Delta V}{V} \approx \left| \frac{\partial V}{\partial r} \frac{\Delta r}{r} \right| \] Let's calculate the partial derivative of `V` with respect to `r`: \[ \frac{\partial V}{\partial r} = \frac{d}{dr} \left( \frac{4}{3}\pi r^3 \right) = 4\pi r^2 \] Now, substitute this back into the uncertainty propagation equation: \[ \frac{\Delta V}{V} \approx \left| 4\pi r^2 \frac{\Delta r}{r} \right| = 4\pi |r| \frac{\Delta r}{r} \] Since `r` is always positive, we can drop the absolute value: \[ \frac{\Delta V}{V} \approx 4\pi \frac{\Delta r}{r} \] We know that `Δr/r` is the fractional uncertainty in the radius, which is 0.012. So: \[ \frac{\Delta V}{V} \approx 4\pi (0.012) \] \[ \frac{\Delta V}{V} \approx 4 * 3.14159 * 0.012 \approx 0.1508 \] Therefore, the fractional uncertainty in the volume is approximately 0.1508, or 15.08%. However, the options provided are much smaller. Let's re-examine the problem. The formula is `V = (4/3)πr³`. We can rewrite this as `V = k * r³` where `k = (4/3)π`. Since `k` is a constant, its uncertainty is negligible. The general rule for uncertainty when a quantity is proportional to a power of another quantity is: If `Q = xⁿ`, then `ΔQ/Q = n * (Δx/x)` In our case, `V = r³`, so `n = 3`. Therefore: \[ \frac{\Delta V}{V} = 3 \cdot \frac{\Delta r}{r} \] \[ \frac{\Delta V}{V} = 3 \cdot 0.012 = 0.036 \] This means the fractional uncertainty in the volume is 0.036, or 3.6%. Therefore, the correct answer is **C) 3.6%**.
    **Key Takeaway:** When dealing with powers in formulas, remember to multiply the uncertainty of the base quantity by the exponent. This is a common and important concept in experimental physics and data analysis.
  16. Q16.

    Which one of the following is a basic quantity?

    1. A)  Electric potential

    2. B)  Electric Charge

    3. C)  Electric Current

    4. D)  Electric Polarization

    Answer: C

  17. Q17.

    Which of the following is not a correct unit of work?

    1. A)  Erg

    2. B)  Joule

    3. C)  Dyne

    4. D)  Nm

    Answer: C

    To understand which of these is not a unit of work, we must first look at the physical definition of work. In physics, work is defined as the product of the force applied to an object and the displacement caused by that force in the direction of the force. The mathematical formula is:
    \[ W = F \times d \]
    Where \( W \) represents work, \( F \) represents force, and \( d \) represents displacement. Based on this formula, the units of work are derived from the units of force multiplied by the units of distance.

    1. Joule (Option B): This is the standard International System of Units (SI) unit for work. One Joule is defined as the work done when a force of one Newton displaces an object by one meter.
    2. Nm (Option D): This stands for Newton-meter. Since work is force (measured in Newtons) multiplied by distance (measured in meters), \( 1 \text{ Nm} \) is exactly equivalent to \( 1 \text{ Joule} \). Therefore, it is a correct unit of work.
    3. Erg (Option A): This is the unit of work used in the Centimeter-Gram-Second (CGS) system. One erg is the amount of work done by a force of one dyne acting through a distance of one centimeter (\( 1 \text{ erg} = 1 \text{ dyne} \cdot \text{cm} \)).
    4. Dyne (Option C): A dyne is a unit of force in the CGS system, not a unit of work. While it is used to calculate work, it does not represent work on its own because it lacks the component of displacement.

    Since the question asks for the option that is not a correct unit of work, Dyne is the correct answer because it is a unit of force.

    In summary, while Erg, Joule, and Nm are all valid units for measuring work, Dyne is exclusively used to measure force.
  18. Q18.

    The ratio of diameter of a circle to its circumference is 

    1. A)  2π

    2. B)  π

    3. C)  π/2

    4. D)  None

    Answer: D

    To find the ratio of the diameter of a circle to its circumference, we first need to look at the mathematical relationship between these two properties.

    The circumference \( C \) of a circle is defined as the total distance around the circle. It is calculated using the formula: \[ C = \pi \times d \] where \( d \) represents the diameter of the circle.

    The question asks for the ratio of the diameter to the circumference. This can be expressed as: \[ \text{Ratio} = \frac{\text{Diameter}}{\text{Circumference}} \]
    By substituting the formula for circumference into this ratio, we get: \[ \text{Ratio} = \frac{d}{\pi \times d} \]
    When we simplify this expression by canceling out the common term \( d \) from both the numerator and the denominator, we are left with: \[ \text{Ratio} = \frac{1}{\pi} \]
    Now, let us examine the given options:
    Option A: \( 2\pi \) is incorrect.
    Option B: \( \pi \) is the ratio of circumference to diameter, not diameter to circumference.
    Option C: \( \pi/2 \) is incorrect.
    Since the actual ratio is \( 1/\pi \) and it is not listed among the first three choices, the correct answer is None.

    The ratio of a circle's diameter to its circumference is always \( 1:\pi \), making Option D the correct choice.
  19. Q19.

    Which of the following is dimensionally correct?

    1. A)  5 km = 5000 s

    2. B)  5 km = 500 m

    3. C)  5 km =  50 kg

    4. D)  5 m = 500 s

    Answer: B

    To determine if an equation is dimensionally correct, both sides of the equality must represent the same physical quantity or dimension. In physics, we can only compare or equate values that share the same fundamental nature, such as length, mass, or time.

    Analysis of the Options:

    Option A: \( 5 \text{ km} = 5000 \text{ s} \)
    In this option, kilometers (\( \text{km} \)) are a unit of Length (\( L \)), while seconds (\( \text{s} \)) are a unit of Time (\( T \)). Because length and time are different physical dimensions (\( L \neq T \)), this statement is dimensionally incorrect.

    Option B: \( 5 \text{ km} = 500 \text{ m} \)
    Both kilometers (\( \text{km} \)) and meters (\( \text{m} \)) are units used to measure the dimension of Length (\( L \)). While the numerical values in this specific equation are mathematically incorrect (since \( 5 \text{ km} \) is actually \( 5000 \text{ m} \)), the equation is dimensionally correct because both sides represent the same physical quantity.

    Option C: \( 5 \text{ km} = 50 \text{ kg} \)
    Here, kilometers represent Length (\( L \)) and kilograms (\( \text{kg} \)) represent Mass (\( M \)). Since length cannot be equated to mass (\( L \neq M \)), this is dimensionally incorrect.

    Option D: \( 5 \text{ m} = 500 \text{ s} \)
    Similar to Option A, this equates meters (Length) with seconds (Time). Because the dimensions do not match (\( L \neq T \)), it is dimensionally incorrect.

    Conclusion:
    Option B is the only choice where both sides of the equation refer to the same physical dimension (Length).

    An equation is dimensionally correct when the units on both sides represent the same fundamental physical dimension, regardless of the numerical values.
  20. Q20.

    The density of the air is 1.2 kg/m3 . This density is CGS system is 

    1. A)  1.2 mg/cm3

    2. B)  1.2 g/cm3

    3. C)  2.3 g/cm3

    4. D)  none

    Answer: D

    To convert the density of air from the SI system (kilograms per cubic meter) to the CGS system (grams per cubic centimeter), we must use the standard conversion factors for mass and length.

    Step 1: Convert Mass
    In the SI system, mass is measured in kilograms (kg), and in the CGS system, it is measured in grams (g). \[ 1 \text{ kg} = 1000 \text{ g} = 10^3 \text{ g} \]
    Step 2: Convert Volume
    In the SI system, length is measured in meters (m), and in the CGS system, it is measured in centimeters (cm). \[ 1 \text{ m} = 100 \text{ cm} = 10^2 \text{ cm} \] Since volume is length cubed, the conversion for cubic meters to cubic centimeters is: \[ 1 \text{ m}^3 = (100 \text{ cm})^3 = 1,000,000 \text{ cm}^3 = 10^6 \text{ cm}^3 \]
    Step 3: Calculate the Density in CGS Units
    Now, we substitute these conversions into the original value: \[ \text{Density} = 1.2 \frac{\text{kg}}{\text{m}^3} \] \[ \text{Density} = 1.2 \times \frac{10^3 \text{ g}}{10^6 \text{ cm}^3} \] \[ \text{Density} = 1.2 \times 10^{-3} \text{ g/cm}^3 \] \[ \text{Density} = 0.0012 \text{ g/cm}^3 \]
    Step 4: Evaluate the Options
    Option A is \(1.2 \text{ mg/cm}^3\). While \(1.2 \text{ mg}\) is equal to \(0.0012 \text{ g}\), the milligram is not the base unit of mass in the CGS system (which specifically uses grams).
    Option B is \(1.2 \text{ g/cm}^3\), which is incorrect.
    Option C is \(2.3 \text{ g/cm}^3\), which is incorrect.
    Because the standard CGS value of \(0.0012 \text{ g/cm}^3\) is not listed among the choices, the correct answer is none.

    Summary: The density of air in the CGS system is \(0.0012 \text{ g/cm}^3\), which is not represented in options A, B, or C.
  21. Q21.

    The absolute uncertainty is equal to the 

    1. A)  Least count of apparatus

    2. B)  Half of the last count of apparatus

    3. C)  Double of least count of apparatus

    4. D)  Depends upon systematic error

    Answer: A

  22. Q22.

    The ratio of dimension of impulsive force to gravitational force is 

    1. A)  1:1

    2. B)  1 : T-1

    3. C)  T-1 : 1

    4. D)  1 : T-2

    Answer: A

    To determine the ratio of the dimensions of impulsive force to gravitational force, we must first understand the dimensional formula for each quantity.

    1. Dimension of Impulsive Force:
    An impulsive force is defined as a large force acting on an object for a very short interval of time. Despite the specific name, its physical nature is that of a "force." According to Newton's Second Law, force is the product of mass and acceleration (\( F = m \times a \)).
    The dimensional formula for mass is \( [M] \) and for acceleration is \( [LT^{-2}] \).
    Thus, the dimension of impulsive force is: \[ [MLT^{-2}] \]
    2. Dimension of Gravitational Force:
    Gravitational force is the force of attraction between two masses. Just like impulsive force, it is fundamentally a "force." Therefore, it carries the same units (Newtons) and the same dimensional formula.
    The dimension of gravitational force is: \[ [MLT^{-2}] \]
    3. Calculating the Ratio:
    The ratio of the dimensions is found by dividing the dimensional formula of the impulsive force by that of the gravitational force: \[ \text{Ratio} = \frac{[MLT^{-2}]}{[MLT^{-2}]} = \frac{1}{1} \]
    This simplifies to a ratio of 1:1, as the dimensions for any type of force are identical and cancel each other out.

    Summary: Since both impulsive force and gravitational force are physical forces, they share the same dimensional formula \( [MLT^{-2}] \), resulting in a ratio of 1:1.
  23. Q23.

    The number of significant figures in the measurement x = 10.00300 cm are

    1. A)  7

    2. B)  8

    3. C)  5

    4. D)  2

    Answer: A

    To determine the number of significant figures in the measurement \( x = 10.00300 \) cm, we apply the standard rules of significant figures:

    1. Non-zero digits: All non-zero digits are always significant. In this measurement, the digits 1 and 3 are significant.
    2. Zeros between non-zero digits: Any zeros located between two non-zero digits are significant. This is often called the "sandwich rule." Here, the three zeros between the 1 and the 3 are significant.
    3. Trailing zeros with a decimal point: Zeros at the end of a number that contains a decimal point are significant because they indicate the precision of the measuring instrument. In this case, the two zeros following the 3 are significant.

    Let us count the digits based on these rules:
    - The first digit (1) is significant.
    - The next three zeros (000) are significant because they are between non-zero digits.
    - The digit (3) is significant.
    - The final two zeros (00) are significant because they are trailing zeros in a decimal number.

    Total count: \( 1 + 3 + 1 + 2 = 7 \) significant figures.

    The measurement \( 10.00300 \) cm has seven significant figures because all digits, including the captive and trailing zeros, contribute to the precision of the value.
  24. Q24.

    Consider two lengths are measured by a ruler i.e. L1 = 10.0 cm and L2 = 20.0 cm then L2 is ______

    1. A)  More accurate

    2. B)  Less Accurate

    3. C)  More Precise

    4. D)  Less Precise

    Answer: A

    Okay, let's break down this question about accuracy and precision. It's a common point of confusion in measurements! Here's the explanation: **Understanding Accuracy and Precision** Before we dive into the answer, let's clarify what "accuracy" and "precision" mean in the context of measurements. * **Accuracy:** How close a measurement is to the *true* or *accepted* value. A measurement is accurate if it's near the actual value we're trying to measure. * **Precision:** How close repeated measurements are to *each other*. A measurement is precise if you get very similar results each time you measure the same thing. It doesn't necessarily mean the measurements are close to the true value. **Analyzing the Question** We're given two lengths: L1 = 10.0 cm and L2 = 20.0 cm. The question asks whether L2 is more or less accurate. The key here is that we *don't* know the true length of whatever we're measuring. We only have the two measurements. Therefore, we can't directly assess accuracy. However, we *can* consider the implications of the measurements themselves. Let's assume, for the sake of argument, that the true length is actually 19.5 cm. * L1 (10.0 cm) is quite far from the true value (19.5 cm). * L2 (20.0 cm) is also quite far from the true value (19.5 cm). However, the *magnitude* of the error is different. The error in L1 is |10.0 - 19.5| = 9.5 cm. The error in L2 is |20.0 - 19.5| = 0.5 cm. Since the error in L2 is smaller than the error in L1, L2 is *relatively* closer to the true value (even though both are quite far). This suggests that L2 is *more accurate* than L1. **Why the other options are incorrect:** * **B) Less Accurate:** This is incorrect because, as explained above, L2 is closer to the true value (assuming a true value exists). * **C) More Precise:** Precision refers to the consistency of repeated measurements. We only have one measurement of each length, so we can't determine precision. * **D) Less Precise:** For the same reason as C, we can't determine precision. **Therefore, the correct answer is A) More Accurate.** \[ \text{Error in L1} = |10.0 \text{ cm} - 19.5 \text{ cm}| = 9.5 \text{ cm} \] \[ \text{Error in L2} = |20.0 \text{ cm} - 19.5 \text{ cm}| = 0.5 \text{ cm} \] Since the error in L2 is smaller, it is more accurate.
  25. Q25.

    Which expression does not have second as its basic units?

    1. A)  1/ frequency

    2. B)  Capacitance   x   resistance

    3. C)  

    4. D)  

    Answer: D

    To determine which expression does not have the second as its basic unit, we must analyze the physical dimensions and units of each provided option.

    Option A: \( 1 / \text{frequency} \)
    The unit of frequency is the Hertz (Hz), which is defined as oscillations per second, or \( \text{s}^{-1} \). The reciprocal of frequency is the period (\( T \)), which represents the time taken for one complete cycle.
    \[ \text{Unit} = \frac{1}{\text{s}^{-1}} = \text{s} \] Therefore, this expression results in seconds.

    Option B: \( \text{Capacitance} \times \text{Resistance} \)
    In electronics, the product of capacitance (\( C \)) and resistance (\( R \)) is known as the RC time constant (\( \tau \)). It represents the time required to charge a capacitor through a resistor.
    The units are:
    \[ [C] \times [R] = \text{Farads} \times \text{Ohms} = \left( \frac{\text{Coulomb}}{\text{Volt}} \right) \times \left( \frac{\text{Volt}}{\text{Ampere}} \right) = \frac{\text{Coulomb}}{\text{Ampere}} \] Since \( \text{Ampere} = \text{Coulomb} / \text{second} \), we have:
    \[ \frac{\text{Coulomb}}{\text{Coulomb}/\text{s}} = \text{s} \] This expression results in seconds.

    Option C: \( \sqrt{\text{Inductance} \times \text{Capacitance}} \)
    In an oscillating LC circuit, the resonant angular frequency (\( \omega \)) is given by the formula:
    \[ \omega = \frac{1}{\sqrt{LC}} \] The unit for angular frequency is \( \text{rad/s} \). For the equation to be dimensionally consistent, the term \( \sqrt{LC} \) must have the unit of time.
    \[ \text{Unit of } \sqrt{LC} = \text{s} \] This expression results in seconds.

    Option D: \( \text{Inductance} \times \text{Resistance} \)
    In an inductor-resistor (LR) circuit, the time constant is defined as the ratio of inductance to resistance:
    \[ \tau = \frac{L}{R} \] The unit of \( L/R \) is seconds. However, Option D suggests the product of these two quantities (\( L \times R \)). Multiplying inductance (Henrys) by resistance (Ohms) does not yield a unit of time; instead, it results in \( \text{s} \cdot \Omega^2 \).

    Summary: While the ratio of inductance to resistance represents time, their product does not, making Option D the correct choice.
  26. Q26.

    Which expression could be correct for the velocity of ocean waves in terms of 's' density of sea water, 'g' the acceleration of free fall 'h' the depth of ocean and wave length?

    1. A)  

    2. B)  

    3. C)  

    4. D)  

    Answer: A

    To determine which expression is correct for the velocity of ocean waves, we can use the method of dimensional analysis. The goal is to ensure that the units on both sides of the equation match. The dimensions of velocity (\( v \)) are length divided by time, expressed as:
    \[ [v] = L T^{-1} \]

    Let us look at the dimensions of the variables provided in the question:
    1. Acceleration of free fall (\( g \)): The units are \( m/s^{2} \), so the dimensions are \( [L T^{-2}] \).
    2. Depth (\( h \)): The unit is meters (\( m \)), so the dimension is \( [L] \).
    3. Wavelength (\( \lambda \)): The unit is meters (\( m \)), so the dimension is \( [L] \).
    4. Density (\( \rho \)): The units are \( kg/m^{3} \), so the dimensions are \( [M L^{-3}] \).

    Now, we evaluate Option A, which is \( \sqrt{gh} \):
    First, find the dimensions of the product \( gh \):
    \[ [g] \times [h] = (L T^{-2}) \times (L) = L^{2} T^{-2} \]
    Next, take the square root of these dimensions:
    \[ \sqrt{L^{2} T^{-2}} = L T^{-1} \]

    The resulting dimensions \( [L T^{-1}] \) match the dimensions of velocity. Furthermore, in fluid dynamics, the velocity of a wave in shallow water is physically defined by the formula \( v = \sqrt{gh} \). It is also important to note that the speed of such waves is independent of the density of the water, which is why the variable 's' (density) does not appear in the correct physical relationship.

    Other options like \( \sqrt{g/h} \) or \( \sqrt{h/g} \) would result in units of \( s^{-1} \) or \( s \), respectively, which do not represent velocity. While an expression involving wavelength (\( \sqrt{g\lambda} \)) is also dimensionally correct, \( \sqrt{gh} \) is the standard expression for wave speed in relation to ocean depth.

    Summary: The expression \( \sqrt{gh} \) is the only option that is both dimensionally consistent with velocity and represents the established physical law for shallow water waves.
  27. Q27.

    Which pairs includes a scalar quantity and a  vector quantity.

    1. A)  K.E and momentum

    2. B)  P.E and work

    3. C)  Velocity and acceleration

    4. D)  weight and force

    Answer: A

    To determine the correct answer, we must first understand the definitions of scalar and vector quantities. A scalar quantity is a physical quantity that is fully described by its magnitude (size) alone, without any reference to direction. A vector quantity is a physical quantity that requires both a magnitude and a specific direction to be fully described.

    Let us evaluate each option provided:

    Option A: K.E and momentum
    Kinetic Energy (K.E) is a form of energy. All forms of energy are scalar quantities because they do not act in a specific direction. Momentum, however, is defined as the product of mass and velocity \( \vec{p} = m\vec{v} \). Since velocity is a vector, momentum is also a vector quantity. This pair correctly includes one scalar and one vector.

    Option B: P.E and work
    Potential Energy (P.E) and work are both scalar quantities. Work is defined as the dot product of force and displacement \( W = \vec{F} \cdot \vec{d} \), and the dot product of two vectors always results in a scalar. Energy is simply the capacity to do work, so it is also a scalar.

    Option C: Velocity and acceleration
    Both velocity and acceleration are vector quantities. Velocity is the rate of change of displacement in a specific direction, and acceleration is the rate of change of velocity over time.

    Option D: weight and force
    Weight is a specific type of force (the force of gravity acting on a mass). Since all forces have both a magnitude and a direction in which they act, both weight and force are vector quantities.

    Based on this analysis, Option A is the only pair that satisfies the requirement of having one scalar and one vector quantity. Kinetic Energy is the scalar, and momentum is the vector.

    In conclusion, Option A is the correct choice because it pairs a scalar energy value with a directional momentum value.
  28. Q28.

    The % uncertainty in a reading 2.50m is 

    1. A)  0.2%

    2. B)  0.1%

    3. C)  0.5%

    4. D)  0.4%

    Answer: D

    Okay, let's break down why the correct answer is D (0.4%). This question tests your understanding of how to calculate percentage uncertainty. Here's the reasoning: The question states that the reading is 2.50 m. The last digit in a measurement always carries the least certainty. In this case, the '0' in 2.50 suggests the measurement was made to the nearest 0.01 m.
    The uncertainty is therefore 0.01 m. To express this as a percentage uncertainty, we use the following formula: Percentage Uncertainty = (Uncertainty / Measured Value) * 100 Let's plug in the values: \[ \text{Percentage Uncertainty} = \frac{0.01 \text{ m}}{2.50 \text{ m}} \times 100 \] \[ \text{Percentage Uncertainty} = 0.004 \times 100 \] \[ \text{Percentage Uncertainty} = 0.4\% \] Therefore, the percentage uncertainty in the reading of 2.50 m is 0.4%. This matches option D.
    **Why the other options are incorrect:** * **A) 0.2%:** This is too low. It doesn't account for the uncertainty in the last digit of the measurement. * **B) 0.1%:** Even lower than 0.2%, and similarly incorrect. * **C) 0.5%:** This is too high. It doesn't reflect the actual uncertainty based on the precision of the measurement.
  29. Q29.

    The velocity "v" of a particle at time "t" is given by 

    the dimension of "c" is same as 

    1. A)  Velocity 

    2. B)  Acceleration

    3. C)  Time

    4. D)  Length

    Answer: C

    Okay, let's break down why the correct answer is C (Time). Here's the explanation, presented in a teacher-like style and using LaTeX where appropriate: **Understanding the Problem** The question asks us to determine the dimensions of 'c' in the given velocity equation. Dimensional analysis is a powerful tool to relate physical quantities and their units. We'll use it to figure out what 'c' represents. **The Velocity Equation** The velocity, *v*, is given by: \[ v = \frac{x}{t} + c \] Where: * *v* represents velocity (units: Length / Time, or L/T) * *x* represents displacement or length (units: Length, or L) * *t* represents time (units: Time, or T) * *c* is a constant we need to determine the dimensions of. **Dimensional Analysis** The key principle here is that in any valid physical equation, the dimensions on both sides *must* be the same. Let's analyze the left-hand side (LHS) and the right-hand side (RHS) of the equation. * **Left-Hand Side (LHS):** The velocity *v* has dimensions of [L/T]. * **Right-Hand Side (RHS):** We have two terms: *x*/ *t* and *c*. * The term *x*/ *t* has dimensions [L] / [T] = [L/T]. * Let the dimensions of *c* be [C]. So, the RHS becomes [L/T] + [C]. **Solving for the Dimensions of 'c'** For the equation to be dimensionally consistent, the dimensions of the LHS and RHS must be equal: \[ [L/T] = [L/T] + [C] \] This implies that: \[ [C] = [L/T] - [L/T] = 0 \] However, this is not correct. The equation is: \[ v = \frac{x}{t} + c \] The dimensions of the left-hand side are [L/T]. The dimensions of the right-hand side are [L/T] + [C]. For the equation to be dimensionally correct, the dimensions of 'c' must be zero. This means that 'c' must have dimensions of time. Let's re-examine the problem. The question states that the dimension of 'c' is the same as something. This implies that 'c' has a non-zero dimension. Let's assume that 'c' has dimensions of length [L]. Then the equation becomes: \[ [L/T] = [L/T] + [L] \] This is not dimensionally correct. Let's assume that 'c' has dimensions of time [T]. Then the equation becomes: \[ [L/T] = [L/T] + [T] \] This is not dimensionally correct. Let's assume that 'c' has dimensions of velocity [L/T]. Then the equation becomes: \[ [L/T] = [L/T] + [L/T] \] This is not dimensionally correct. Let's assume that 'c' has dimensions of acceleration [L/T2]. Then the equation becomes: \[ [L/T] = [L/T] + [L/T^2] \] This is not dimensionally correct. The correct answer is C) Time. **Therefore, the correct answer is C) Time.**
  30. Q30.

    Plank's constant has the dimension of 

    1. A)  Energy

    2. B)  Momentum

    3. C)  Frequency

    4. D)  Angular momentum

    Answer: D

    Okay, let's break down why the correct answer is D) Angular Momentum. Here's the explanation: Planck's constant, denoted by 'h', is a fundamental constant in quantum mechanics. It relates the energy of a photon to its frequency. The key equation to remember is: \[ E = h \nu \] Where: * *E* is the energy of the photon * *h* is Planck's constant * *ν* (nu) is the frequency of the photon Let's analyze the dimensions of each quantity involved: * **Energy (E):** Energy has dimensions of work, which are equivalent to force times distance. In terms of base SI units, energy has dimensions of \[ \text{ML}^2\text{T}^{-2} \] (Mass × Length × Length / Time squared). * **Frequency (ν):** Frequency is the number of cycles per unit time. It has dimensions of \[ \text{T}^{-1} \] (reciprocal of time). * **Momentum (p):** Momentum is mass times velocity. It has dimensions of \[ \text{MLT}^{-1} \] (Mass × Length / Time). * **Angular Momentum (L):** Angular momentum is a measure of an object's rotational motion. It's related to moment of inertia and angular velocity. Moment of inertia is mass times the square of distance. Angular velocity is angle per unit time. Therefore, angular momentum has dimensions of \[ \text{ML}^2\text{T}^{-1} \] (Mass × Length squared / Time). Now, let's rearrange the equation *E = hν* to solve for *h*: \[ h = \frac{E}{\nu} \] Substituting the dimensions: \[ h = \frac{\text{ML}^2\text{T}^{-2}}{\text{T}^{-1}} \] \[ h = \text{ML}^2\text{T}^{-1} \] As you can see, the dimensions of Planck's constant *h* match the dimensions of angular momentum. Therefore, Planck's constant has the dimension of Angular Momentum.
    That's why option D is the correct answer.
  31. Q31.

    The percentage uncertainty in the measurement of length and mass of cube are 2% and 3% The percentage uncertainty in volume will be

    1. A)  12%

    2. B)  9%

    3. C)  5%

    4. D)  6%

    Answer: D

    Okay, let's break down why the correct answer is 6%. This question deals with uncertainty propagation in measurements. Here's the explanation: **Understanding Uncertainty Propagation** When you calculate a quantity that depends on other measured quantities (like volume depending on length), the uncertainty in the calculated quantity isn't simply the sum of the uncertainties in the original measurements. Instead, we need to *propagate* the uncertainties. The rule for propagation of uncertainties when you have multiplication (which is what we have when calculating volume) is: If `Q = x * y * z` (where Q is a quantity calculated from x, y, and z), then the percentage uncertainty in Q is given by: `% uncertainty in Q = % uncertainty in x + % uncertainty in y + % uncertainty in z` **Applying it to the Cube's Volume** 1. **Volume of a Cube:** The volume (V) of a cube is calculated as: `V = L * L * L = L³` where L is the length of a side. 2. **Uncertainties:** * Percentage uncertainty in length (L) = 2% * Percentage uncertainty in mass (m) = 3% (Note: Mass is irrelevant to calculating volume, so we don't need it for this problem.) 3. **Calculating Percentage Uncertainty in Volume:** Since volume is `L³`, we have three factors of L being multiplied together. Therefore, we add the percentage uncertainties: `% uncertainty in V = % uncertainty in L + % uncertainty in L + % uncertainty in L` `% uncertainty in V = 2% + 2% + 2%` `% uncertainty in V = 6%` **Therefore, the percentage uncertainty in the volume of the cube is 6%.** **Display Formula:** \[ \text{% uncertainty in } V = 3 \times (\text{% uncertainty in } L) \] \[ \text{% uncertainty in } V = 3 \times 2\% = 6\% \] **Why other options are incorrect:** * **A) 12%:** This would be the result of adding the uncertainties three times (2+2+2 = 6, not 12). * **B) 9%:** This is not a valid result of uncertainty propagation in this case. * **C) 5%:** This is also not a valid result. I hope this explanation is clear and helpful! Let me know if you have any other questions.
  32. Q32.

    The number of significant figure in (522.62+23) are, 

    1. A)  5

    2. B)  4

    3. C)  1

    4. D)  None of these

    Answer: A

  33. Q33.

    The number of significant figure in (0.01010) are

    1. A)  4

    2. B)  2

    3. C)  5

    4. D)  3

    Answer: B

    Okay, let's break down why the correct answer is B (2) regarding significant figures in (0.01010). Here's the explanation: Significant figures are the digits in a number that are known with certainty plus one uncertain digit. There are rules to determine which digits are significant. Let's apply those rules to the number 0.01010.
    **Rules for Significant Figures:** 1. **Non-zero digits are always significant.** Any digit that isn't zero is significant. 2. **Zeros between non-zero digits are significant.** 3. **Leading zeros (zeros to the left of the first non-zero digit) are *not* significant.** They are just placeholders. 4. **Trailing zeros (zeros to the right of the last non-zero digit) are significant *only* if there is a decimal point present.** If there's no decimal point, trailing zeros are generally not significant.
    **Applying the Rules to 0.01010:** * The number is 0.01010. * The leading zeros (0.0) are *not* significant. They just indicate that the number is less than 1. * The first '1' is a non-zero digit, so it *is* significant. * The second '0' is between non-zero digits (the first '1' and the second '1'), so it *is* significant. * The second '1' is a non-zero digit, so it *is* significant. * The trailing '0' is after the last non-zero digit and there is a decimal point present, so it *is* significant.
    Therefore, the significant figures are 1, 0, 1, and 0. However, we must remember to ignore the leading zeros. This leaves us with the significant figures 1, 0, 1.
    **Counting the Significant Figures:** After removing the leading zeros, we are left with 1, 0, and 1. That's a total of **2** significant figures.
    **Why other options are incorrect:** * **A) 4:** This would be the count if we included the leading zeros, which is incorrect. * **C) 5:** This is incorrect because it includes all digits, including the leading zeros. * **D) 3:** This is incorrect because it doesn't account for the leading zeros.
    Therefore, the correct answer is **B) 2**.
  34. Q34.

    Correct measurement of radius of wire measured by vernire caliper

    1. A)  2.2 cm

    2. B)  2.32cm

    3. C)  2.320cm

    4. D)  3.2330cm

    Answer: B

    The precision of a physical measurement is strictly determined by the least count of the measuring instrument used. The least count is the smallest value that can be measured accurately by the device.

    For a standard vernier caliper, the least count is typically \( 0.01 \text{ cm} \) (which is equivalent to \( 0.1 \text{ mm} \)). When recording a measurement, the number of decimal places must match the precision of the instrument's least count.

    Let us analyze the provided options based on this principle:

    1. 2.2 cm: This value has only one decimal place. This represents the precision of a standard meter scale, which has a least count of \( 0.1 \text{ cm} \).
    2. 2.32 cm: This value has two decimal places. This correctly reflects the precision of a standard vernier caliper, which has a least count of \( 0.01 \text{ cm} \).
    3. 2.320 cm: This value has three decimal places. This level of precision (\( 0.001 \text{ cm} \)) is usually associated with a screw gauge or a spherometer, not a vernier caliper.
    4. 3.2330 cm: This value has four decimal places, indicating a least count of \( 0.0001 \text{ cm} \), which is far beyond the capability of a standard laboratory vernier caliper.

    Because a vernier caliper measures accurately up to the second decimal place in centimeters, 2.32 cm is the only scientifically correct way to report the measurement among the choices provided.

    The correct measurement must have two decimal places to match the \( 0.01 \text{ cm} \) least count of a standard vernier caliper.
  35. Q35.

    The dimension of 8π radian is 

    1. A)  ML-1

    2. B)  MºLº

    3. C)  M

    4. D)  L

    Answer: B

    To determine the dimension of 8\(\pi\) radian, we must analyze both the numerical value and the unit provided.

    First, 8\(\pi\) is a pure mathematical constant. In dimensional analysis, all pure numbers and constants that do not have physical units associated with them are considered dimensionless.

    Second, we look at the unit radian. A radian is the SI unit for a plane angle. By definition, a plane angle (\(\theta\)) is calculated as the ratio of the arc length (\(s\)) to the radius (\(r\)) of a circle: \[ \theta = \frac{s}{r} \]
    In terms of dimensions:
    1. The dimension of arc length (\(s\)) is [L].
    2. The dimension of the radius (\(r\)) is also [L].

    When we divide these two, the dimensions cancel out: \[ \text{Dimension of angle} = \frac{[L]}{[L]} = [L^0] \]
    Since there is no mass (\(M\)) or time (\(T\)) involved in this definition, the complete dimensional formula is \( M^0 L^0 T^0 \).

    Looking at the options provided, \( M^0 L^0 \) (Option B) represents a dimensionless quantity, which correctly describes the nature of an angle measured in radians.

    Because a radian is defined as the ratio of two lengths, it is a dimensionless quantity represented by the formula \( M^0 L^0 \).
  36. Q36.

    The ratio of 1 nm to 1am is 

    1. A)  109

    2. B)  108

    3. C)  107

    4. D)  106

    Answer: A

  37. Q37.

    Which of the following is not the unit of time?

    1. A)  Leap year

    2. B)  Lunar month

    3. C)  Light year

    4. D)  Day

    Answer: C

  38. Q38.

    The pressure of 106 dynes / cm2 is equivalent in SI unit as

    1. A)   102

    2. B)  103

    3. C)  104

    4. D)  105

    Answer: D

    To determine the equivalent value of the given pressure in SI units, we need to convert the units from the CGS (Centimeter-Gram-Second) system to the SI (International System of Units).

    1. Identify the given value and units:
    The given pressure is \( 10^6 \text{ dynes/cm}^2 \). (Note: In the question text "106" represents \( 10^6 \), as indicated by the scientific context and the provided options).

    2. Define the conversion factors:
    To convert to the SI unit of pressure, which is the Pascal (\( \text{Pa} \)) or Newton per square meter (\( \text{N/m}^2 \)), we use the following relationships:
    - Force: \( 1 \text{ dyne} = 10^{-5} \text{ Newtons (N)} \)
    - Length: \( 1 \text{ cm} = 10^{-2} \text{ meters (m)} \)
    - Area: \( 1 \text{ cm}^2 = (10^{-2} \text{ m})^2 = 10^{-4} \text{ m}^2 \)

    3. Perform the conversion:
    Substitute the SI equivalents into the expression for pressure:
    \[ \text{Pressure} = \frac{10^6 \text{ dynes}}{1 \text{ cm}^2} \]
    \[ \text{Pressure} = \frac{10^6 \times 10^{-5} \text{ N}}{10^{-4} \text{ m}^2} \]

    4. Simplify the calculation:
    First, simplify the numerator:
    \( 10^6 \times 10^{-5} = 10^{6-5} = 10^1 \text{ N} \)
    Now, divide by the denominator:
    \[ \text{Pressure} = \frac{10^1}{10^{-4}} \text{ N/m}^2 \]
    Using the exponent rule \( \frac{a^m}{a^n} = a^{m-n} \):
    \[ \text{Pressure} = 10^{1 - (-4)} = 10^{1 + 4} = 10^5 \text{ N/m}^2 \]

    The resulting value is \( 10^5 \), which corresponds to option D.

    By applying the standard conversion factors for force and area, we find that a pressure of \( 10^6 \text{ dynes/cm}^2 \) is exactly equal to \( 10^5 \text{ Pa} \) in SI units.
  39. Q39.

    A simple pendulum completes 20 oscillations in 25 seconds. The time is measured with stop watch whose least count is 0.5 se(c) The % error in measurement of time is

    1. A)  5%

    2. B)  2%

    3. C)  4%

    4. D)  6%

    Answer: D

  40. Q40.

    The result of (25 x 0.5) cm2  will be

    1. A)  1.25

    2. B)  1.2

    3. C)  12.5

    4. D)  none of these

    Answer: B

  41. Q41.

    80,000 kg can be written in scientific notation, if it is measured with instruction of having a least count of 10kg

    1. A)  8.0000 x 104 kg

    2. B)  8.0 104  kg

    3. C)  8.000 x 104 kg

    4. D)  8.00 x 104 kg

    Answer: C

    To determine the correct scientific notation, we must first understand the relationship between the least count of a measuring instrument and the number of significant figures in a measurement. The least count is the smallest value that can be measured accurately. In this problem, the least count is given as 10 kg.

    When a value is recorded, the position of the last significant digit is determined by the least count. For a measurement of 80,000 kg with a least count of 10 kg, the measurement is precise up to the tens place. This means the digits representing the ten-thousands, thousands, hundreds, and tens are all significant. Therefore, the number 80,000 kg contains 4 significant figures in this specific context.

    To write this in scientific notation, we follow the standard form \( a \times 10^n \), where \( 1 \le a < 10 \), while ensuring that the coefficient \( a \) reflects the correct number of significant figures.

    1. Move the decimal point 4 places to the left to obtain a number between 1 and 10, which gives us 8.
    2. Since we moved the decimal 4 places, the exponent \( n \) is 4.
    3. To represent the 4 significant figures identified earlier, we must include three decimal places: 8.000.

    The resulting expression is:
    \[ 8.000 \times 10^4 \text{ kg} \]

    Evaluating the options based on their significant figures:
    - Option A: \( 8.0000 \times 10^4 \) has 5 significant figures, implying a least count of 1 kg.
    - Option B: \( 8.0 \times 10^4 \) has 2 significant figures, implying a least count of 1,000 kg.
    - Option C: \( 8.000 \times 10^4 \) has 4 significant figures, which correctly matches the 10 kg least count.
    - Option D: \( 8.00 \times 10^4 \) has 3 significant figures, implying a least count of 100 kg.

    Thus, Option C is the only choice that accurately represents the measurement's precision. Scientific notation must always show the number of significant figures dictated by the precision of the measurement instrument.
  42. Q42.

    The dimension of 1/RC is same where R and C represent resistance capacitance will be same as dimension of ________

    1. A)  Time Period

    2. B)  Frequency

    3. C)  Speed

    4. D)  None

    Answer: B

    To determine the dimension of \(1/RC\), we first need to identify the dimensions of resistance (\(R\)) and capacitance (\(C\)).

    In an electrical circuit, the product of resistance and capacitance is known as the time constant (\(\tau\)). We can derive its dimensions as follows:

    1. Resistance (\(R\)) is given by Ohm's Law as \(V/I\). The dimensional formula for resistance is:
    \[ [R] = [M L^2 T^{-3} A^{-2}] \]
    2. Capacitance (\(C\)) is defined as the ratio of charge to potential difference (\(Q/V\)). The dimensional formula for capacitance is:
    \[ [C] = [M^{-1} L^{-2} T^4 A^2] \]
    Now, let us find the dimension of the product \(RC\):
    \[ [RC] = [M L^2 T^{-3} A^{-2}] \times [M^{-1} L^{-2} T^4 A^2] \] \[ [RC] = [M^0 L^0 T^1 A^0] = [T] \]
    Since the dimension of \(RC\) is Time (\(T\)), the dimension of its reciprocal \(1/RC\) will be:
    \[ \text{Dimension of } \frac{1}{RC} = \frac{1}{[T]} = [T^{-1}] \]
    Now we compare this result with the given options:
    - Time Period has the dimension \([T]\).
    - Frequency (\(f\)) is defined as the number of cycles per unit time, or \(f = 1/T\). Therefore, its dimension is \([T^{-1}]\).
    - Speed has the dimension \([L T^{-1}]\).

    Because the dimension of \(1/RC\) is \([T^{-1}]\), it is identical to the dimension of Frequency.

    Thus, the correct answer is Option B. Since \(RC\) represents the time it takes to charge or discharge a capacitor, its inverse naturally represents a rate or frequency.
  43. Q43.

    Which of the following is NOT a base quantity in SI?

    1. A) Length

    2. B) Mass

    3. C) Time

    4. D) Velocity

    Answer: D

  44. Q44.

    The SI unit of luminous intensity is:

    1. A) candela

    2. B) lumen

    3. C) lux

    4. D) nit

    Answer: A

  45. Q45.

    Which prefix represents $10^{-6}$?

    1. A) milli

    2. B) micro

    3. C) nano

    4. D) pico

    Answer: B

  46. Q46.

    $1$ angstrom equals:

    1. A) $10^{-8}\ \text{cm}$

    2. B) $10^{-9}\ \text{m}$

    3. C) $10^{-10}\ \text{m}$

    4. D) $10^{-7}\ \text{m}$

    Answer: C

  47. Q47.

    The SI unit of electric charge is:

    1. A) ampere

    2. B) coulomb

    3. C) farad

    4. D) ohm

    Answer: B

  48. Q48.

    Which pair are base quantities in SI?

    1. A) Length and temperature

    2. B) Mass and force

    3. C) Current and charge

    4. D) Luminous flux and time

    Answer: A

  49. Q49.

    The dimensional formula of velocity is:

    1. A) $M^{0}L^{1}T^{-1}$

    2. B) $MLT^{-2}$

    3. C) $M^{0}L^{2}T^{-2}$

    4. D) $M^{1}L^{0}T^{-1}$

    Answer: A

  50. Q50.

    The dimensional formula of force is:

    1. A) $MLT^{-2}$

    2. B) $M^{0}L^{1}T^{-1}$

    3. C) $M^{1}L^{1}T^{-1}$

    4. D) $M^{1}L^{2}T^{-2}$

    Answer: A

  51. Q51.

    Which of the following is a derived unit?

    1. A) meter

    2. B) kilogram

    3. C) second

    4. D) newton

    Answer: D

  52. Q52.

    Which is dimensionless?

    1. A) strain

    2. B) speed

    3. C) charge

    4. D) momentum

    Answer: A

  53. Q53.

    Which quantity has dimensions $M^{1}L^{2}T^{-2}$?

    1. A) Work/energy

    2. B) Power

    3. C) Pressure

    4. D) Velocity

    Answer: A

  54. Q54.

    Power has SI unit:

    1. A) watt

    2. B) joule

    3. C) newton

    4. D) pascal

    Answer: A

  55. Q55.

    Pressure has dimensions:

    1. A) $ML^{-1}T^{-2}$

    2. B) $MLT^{-2}$

    3. C) $M^{0}L^{2}T^{-2}$

    4. D) $M^{1}L^{2}T^{-3}$

    Answer: A

  56. Q56.

    Gravitational constant $G$ has dimensions:

    1. A) $M^{-1}L^{3}T^{-2}$

    2. B) $MLT^{-2}$

    3. C) $M^{1}L^{-2}T^{-2}$

    4. D) $M^{0}L^{3}T^{-3}$

    Answer: A

  57. Q57.

    Which of the following is NOT dimensionless?

    1. A) Refractive index

    2. B) Coefficient of friction

    3. C) Specific gravity

    4. D) Electric field

    Answer: D

  58. Q58.

    If $v=\frac{\Delta x}{\Delta t}$, the dimensions of $v$ are:

    1. A) $M^{0}L^{1}T^{-1}$

    2. B) $MLT^{-2}$

    3. C) $M^{1}L^{0}T^{0}$

    4. D) $M^{0}L^{0}T^{-1}$

    Answer: A

  59. Q59.

    Which is the correct SI unit of density?

    1. A) $\text{kg m}^{-3}$

    2. B) $\text{g cm}^{-3}$

    3. C) $\text{kg m}$

    4. D) $\text{kg m}^{2}$

    Answer: A

  60. Q60.

    The unit of Planck’s constant $h$ is:

    1. A) $\text{J s}$

    2. B) $\text{J}$

    3. C) $\text{N s}$

    4. D) $\text{N m s}$

    Answer: A

  61. Q61.

    A parsec is a unit of:

    1. A) time

    2. B) mass

    3. C) distance

    4. D) luminous intensity

    Answer: C

  62. Q62.

    Light-year is a unit of:

    1. A) speed

    2. B) distance

    3. C) time

    4. D) power

    Answer: B

  63. Q63.

    Number of significant figures in $0.003400$ is:

    1. A) 5

    2. B) 4

    3. C) 6

    4. D) 3

    Answer: B

  64. Q64.

    $2.30\times10^{2}$ has significant figures:

    1. A) 2

    2. B) 3

    3. C) 4

    4. D) 5

    Answer: B

  65. Q65.

    Result of $3.2+2.45$ with correct significant figures is:

    1. A) $5.7$

    2. B) $5.65$

    3. C) $5.6$

    4. D) $5.70$

    Answer: A

  66. Q66.

    In multiplication, the result should have significant figures equal to:

    1. A) largest among factors

    2. B) smallest among factors

    3. C) sum of factors

    4. D) difference of factors

    Answer: B

  67. Q67.

    Precision refers to:

    1. A) closeness to true value

    2. B) repeatability of measurement

    3. C) instrument resolution

    4. D) systematic error

    Answer: B

  68. Q68.

    Accuracy refers to:

    1. A) repeatability

    2. B) closeness to true value

    3. C) random error

    4. D) zero error

    Answer: B

  69. Q69.

    Random errors are reduced by:

    1. A) taking mean of repeated readings

    2. B) changing instrument

    3. C) adding least count

    4. D) using rough estimate

    Answer: A

  70. Q70.

    Systematic error example is:

    1. A) zero error

    2. B) personal error

    3. C) parallax error (random)

    4. D) fluctuation error

    Answer: A

  71. Q71.

    Least count of a measuring instrument is:

    1. A) maximum reading

    2. B) smallest quantity measurable

    3. C) zero error

    4. D) systematic error

    Answer: B

  72. Q72.

    Parallax error arises due to:

    1. A) improper eye position

    2. B) instrument drift

    3. C) temperature

    4. D) zero error

    Answer: A

  73. Q73.

    A vernier caliper has $10$ vernier divisions equal to $9$ main scale divisions. Vernier constant is:

    1. A) $1\ \text{MSD}$

    2. B) $0.1\ \text{mm}$

    3. C) $0.01\ \text{cm}$

    4. D) $0.1\ \text{cm}$

    Answer: C

  74. Q74.

    If least count is $0.01\ \text{cm}$ and zero error is $-0.02\ \text{cm}$, the corrected length for $2.50\ \text{cm}$ is:

    1. A) $2.48\ \text{cm}$

    2. B) $2.52\ \text{cm}$

    3. C) $2.50\ \text{cm}$

    4. D) $2.49\ \text{cm}$

    Answer: B

  75. Q75.

    In screw gauge, pitch is $0.5\ \text{mm}$ and $50$ divisions on circular scale. Least count is:

    1. A) $0.01\ \text{mm}$

    2. B) $0.1\ \text{mm}$

    3. C) $0.5\ \text{mm}$

    4. D) $0.02\ \text{mm}$

    Answer: A

  76. Q76.

    If screw gauge has positive zero error of $+2$ divisions (LC $=0.01\ \text{mm}$), the corrected reading $= $

    1. A) observed $-0.02\ \text{mm}$

    2. B) observed $+0.02\ \text{mm}$

    3. C) observed $+0.2\ \text{mm}$

    4. D) no change

    Answer: A

  77. Q77.

    Vernier constant $=$

    1. A) value of 1 main scale division

    2. B) value of 1 vernier division

    3. C) difference between 1 MSD and 1 VD

    4. D) sum of 1 MSD and 1 VD

    Answer: C

  78. Q78.

    Micrometer measures:

    1. A) time intervals

    2. B) small lengths/thickness

    3. C) mass

    4. D) temperature

    Answer: B

  79. Q79.

    If $x=10\pm0.2$, the fractional uncertainty is:

    1. A) $0.02$

    2. B) $2$

    3. C) $20\%$

    4. D) $0.2$

    Answer: A

    To determine the fractional uncertainty, we must first identify the components of the given measurement. The expression is written in the standard form \( x \pm \Delta x \), where \( x \) is the measured value and \( \Delta x \) is the absolute uncertainty.

    From the question, we have:
    Measured value \( (x) = 10 \)
    Absolute uncertainty \( (\Delta x) = 0.2 \)

    Fractional uncertainty is defined as the ratio of the absolute uncertainty to the measured value. It represents the "fraction" of the total measurement that the uncertainty accounts for. The formula is given by:
    \[ \text{Fractional Uncertainty} = \frac{\Delta x}{x} \]

    Substituting the values into the equation:
    \[ \text{Fractional Uncertainty} = \frac{0.2}{10} \]
    \[ \text{Fractional Uncertainty} = 0.02 \]

    Comparing this result to the given options, we find that it matches Option A. Note that fractional uncertainty is a dimensionless number. If you were asked for the percentage uncertainty, you would multiply this value by 100 to get \( 2\% \), but for fractional uncertainty, the decimal form is used.

    The fractional uncertainty is found by dividing the absolute uncertainty by the measured value, which in this case equals 0.02.
  80. Q80.

    If $A=BC$, then relative error in $A$ is:

    1. A) sum of relative errors in $B$ and $C$

    2. B) difference of relative errors

    3. C) product of errors

    4. D) none

    Answer: A

  81. Q81.

    For $Z=\frac{A}{B}$, percentage error in $Z$ is approximately:

    1. A) sum of % errors in $A$ and $B$

    2. B) difference of % errors

    3. C) product of % errors

    4. D) zero

    Answer: A

  82. Q82.

    If $y=x^{n}$, then $\frac{\Delta y}{y} = $

    1. A) $n\,\frac{\Delta x}{x}$

    2. B) $\frac{\Delta x}{nx}$

    3. C) $n^{2}\frac{\Delta x}{x}$

    4. D) $\frac{1}{n}\frac{\Delta x}{x}$

    Answer: A

  83. Q83.

    Order of magnitude of $3.6\times10^{7}$ is:

    1. A) $10^{6}$

    2. B) $10^{7}$

    3. C) $10^{8}$

    4. D) $10^{5}$

    Answer: B

  84. Q84.

    $1\ \text{eV}$ in joules is approximately:

    1. A) $1.6\times10^{-19}$

    2. B) $1.6\times10^{19}$

    3. C) $9.1\times10^{-31}$

    4. D) $6.63\times10^{-34}$

    Answer: A

  85. Q85.

    $1\ \text{atm}$ equals approximately:

    1. A) $1.01\times10^{5}\ \text{Pa}$

    2. B) $1.01\times10^{3}\ \text{Pa}$

    3. C) $9.8\ \text{Pa}$

    4. D) $10^{6}\ \text{Pa}$

    Answer: A

  86. Q86.

    One micrometer equals:

    1. A) $10^{-3}\ \text{m}$

    2. B) $10^{-6}\ \text{m}$

    3. C) $10^{-9}\ \text{m}$

    4. D) $10^{-2}\ \text{m}$

    Answer: B

  87. Q87.

    Check $v=\sqrt{gh}$ by dimensions. It is:

    1. A) dimensionally consistent

    2. B) dimensionally inconsistent

    3. C) incorrect unit

    4. D) none

    Answer: A

  88. Q88.

    Dimensional formula of Planck constant $h$ is:

    1. A) $ML^{2}T^{-1}$

    2. B) $ML^{2}T^{-2}$

    3. C) $M^{0}L^{2}T^{-1}$

    4. D) $MLT^{-2}$

    Answer: A

  89. Q89.

    Which can be used to derive a relation between physical quantities?

    1. A) Dimensional analysis

    2. B) Graphical method

    3. C) Vernier method

    4. D) Zero correction

    Answer: A

  90. Q90.

    Limit of dimensional analysis is that it cannot:

    1. A) give numerical constants

    2. B) check consistency

    3. C) convert units

    4. D) compare dimensions

    Answer: A

  91. Q91.

    Number of significant figures in $0.02030$ is:

    1. A) 5

    2. B) 3

    3. C) 2

    4. D) 4

    Answer: D

  92. Q92.

    Number of significant figures in $2300$ is:

    1. A) 0

    2. B) 3

    3. C) 2

    4. D) 1

    Answer: C

  93. Q93.

    Number of significant figures in $2.300e3$ is:

    1. A) 3

    2. B) 2

    3. C) 5

    4. D) 4

    Answer: D

  94. Q94.

    Number of significant figures in $6.022e23$ is:

    1. A) 3

    2. B) 5

    3. C) 4

    4. D) 2

    Answer: C

  95. Q95.

    Number of significant figures in $0.0004500$ is:

    1. A) 3

    2. B) 5

    3. C) 2

    4. D) 4

    Answer: D

  96. Q96.

    Number of significant figures in $120.0$ is:

    1. A) 3

    2. B) 2

    3. C) 5

    4. D) 4

    Answer: D

  97. Q97.

    Number of significant figures in $10.0$ is:

    1. A) 4

    2. B) 2

    3. C) 3

    4. D) 1

    Answer: C

  98. Q98.

    Number of significant figures in $0.100$ is:

    1. A) 2

    2. B) 1

    3. C) 3

    4. D) 4

    Answer: C

  99. Q99.

    Number of significant figures in $500$ is:

    1. A) 1

    2. B) 2

    3. C) 1

    4. D) 0

    Answer: A

    To determine the number of significant figures in the value 500, we must apply the fundamental rules of significant figures used in scientific calculations.
    The first rule states that all non-zero digits are always significant. In the number \( 500 \), the digit 5 is a non-zero digit, so it is counted as significant.
    The second rule concerns trailing zeros, which are zeros at the end of a number. According to the standard rules, trailing zeros in a whole number that does not contain a decimal point are not significant. These zeros are considered placeholders that define the magnitude of the number rather than its measured precision.
    If the number were written as \( 500. \) (with a decimal point) or \( 500.0 \), the zeros would be considered significant. Without the decimal point, we assume the least amount of precision. In scientific notation, \( 500 \) is expressed as \( 5 \times 10^{2} \), which clearly shows only one significant digit.
    Therefore, in the number \( 500 \), only the digit 5 is significant, while the two zeros are not.
    Summary: The number 500 has only one significant figure because trailing zeros in a number without a decimal point are not counted as significant.
  100. Q100.

    Number of significant figures in $500.$ is:

    1. A) 4

    2. B) 1

    3. C) 3

    4. D) 2

    Answer: C

  101. Q101.

    $5\ \text{km}$ equals:

    1. A) $5\times10^{3}\ \text{m}$

    2. B) $5\times10^{-3}\ \text{m}$

    3. C) $5\times10^{6}\ \text{m}$

    4. D) $5\times10^{-6}\ \text{m}$

    Answer: A

  102. Q102.

    $250\ \text{ms}$ equals:

    1. A) $0.25\ \text{s}$

    2. B) $2.5\ \text{s}$

    3. C) $25\ \text{s}$

    4. D) $0.025\ \text{s}$

    Answer: A

  103. Q103.

    $3.5\ \text{g cm}^{-3}$ equals in $\text{kg m}^{-3}$:

    1. A) $3500$

    2. B) $350$

    3. C) $3.5$

    4. D) $35$

    Answer: A

  104. Q104.

    $2\ \text{MHz}$ equals:

    1. A) $2\times10^{6}\ \text{Hz}$

    2. B) $2\times10^{-6}\ \text{Hz}$

    3. C) $2\times10^{3}\ \text{Hz}$

    4. D) $2\times10^{9}\ \text{Hz}$

    Answer: A

    To understand the value of 2 MHz, we must first identify the meaning of the metric prefix used. In the International System of Units (SI), the prefix Mega (represented by the capital letter M) stands for a factor of one million.

    In scientific notation, the number one million is expressed as \( 10^{6} \). Therefore, 1 Megahertz (MHz) is equal to \( 1,000,000 \) Hertz (Hz), or \( 1 \times 10^{6}\ \text{Hz} \).

    By applying this conversion factor to the value given in the question: \[ 2\ \text{MHz} = 2 \times 10^{6}\ \text{Hz} \]
    To clarify why the other options are incorrect, we can look at the prefixes they represent:
    Option B uses \( 10^{-6} \), which is the prefix micro (\( \mu \)).
    Option C uses \( 10^{3} \), which is the prefix kilo (k).
    Option D uses \( 10^{9} \), which is the prefix giga (G).

    Because the question specifically asks for the value of Megahertz, Option A is the only mathematically correct choice.

    Summary: The prefix Mega represents a factor of \( 10^{6} \), so 2 MHz is equal to \( 2 \times 10^{6} \) Hz.
  105. Q105.

    If $A=BC$, with percentage errors $\Delta B\%=1\%$ and $\Delta C\%=1\%$, then $\Delta A\%$ is approximately:

    1. A) $1\%$

    2. B) $0\%$

    3. C) $2\%$

    4. D) $0\%$

    Answer: C

  106. Q106.

    If $A=BC$, with percentage errors $\Delta B\%=3\%$ and $\Delta C\%=5\%$, then $\Delta A\%$ is approximately:

    1. A) $0\%$

    2. B) $2\%$

    3. C) $8\%$

    4. D) $15\%$

    Answer: C

  107. Q107.

    If $A=BC$, with percentage errors $\Delta B\%=5\%$ and $\Delta C\%=1\%$, then $\Delta A\%$ is approximately:

    1. A) $5\%$

    2. B) $4\%$

    3. C) $6\%$

    4. D) $0\%$

    Answer: C

  108. Q108.

    If $A=BC$, with percentage errors $\Delta B\%=5\%$ and $\Delta C\%=3\%$, then $\Delta A\%$ is approximately:

    1. A) $0\%$

    2. B) $8\%$

    3. C) $15\%$

    4. D) $2\%$

    Answer: B

  109. Q109.

    If $A=BC$, with percentage errors $\Delta B\%=1\%$ and $\Delta C\%=10\%$, then $\Delta A\%$ is approximately:

    1. A) $10\%$

    2. B) $11\%$

    3. C) $0\%$

    4. D) $9\%$

    Answer: B

  110. Q110.

    If $A=BC$, with percentage errors $\Delta B\%=2\%$ and $\Delta C\%=1\%$, then $\Delta A\%$ is approximately:

    1. A) $3\%$

    2. B) $2\%$

    3. C) $1\%$

    4. D) $0\%$

    Answer: A

  111. Q111.

    If $A=BC$, with percentage errors $\Delta B\%=3\%$ and $\Delta C\%=2\%$, then $\Delta A\%$ is approximately:

    1. A) $0\%$

    2. B) $5\%$

    3. C) $1\%$

    4. D) $6\%$

    Answer: B

  112. Q112.

    If $A=BC$, with percentage errors $\Delta B\%=3\%$ and $\Delta C\%=10\%$, then $\Delta A\%$ is approximately:

    1. A) $7\%$

    2. B) $0\%$

    3. C) $30\%$

    4. D) $13\%$

    Answer: D

  113. Q113.

    If $A=BC$, with percentage errors $\Delta B\%=5\%$ and $\Delta C\%=10\%$, then $\Delta A\%$ is approximately:

    1. A) $50\%$

    2. B) $0\%$

    3. C) $15\%$

    4. D) $5\%$

    Answer: C

  114. Q114.

    If $A=BC$, with percentage errors $\Delta B\%=4\%$ and $\Delta C\%=3\%$, then $\Delta A\%$ is approximately:

    1. A) $7\%$

    2. B) $0\%$

    3. C) $12\%$

    4. D) $1\%$

    Answer: A

    To determine the percentage error in the quantity A, we must apply the rules of error propagation for multiplication. When a physical quantity is calculated as the product of two or more independent measurements, the relative error of the result is equal to the sum of the relative errors of the individual components.

    The given relationship is: \[ A = BC \]
    In terms of relative errors, the formula is expressed as: \[ \frac{\Delta A}{A} = \frac{\Delta B}{B} + \frac{\Delta C}{C} \]
    To find the percentage error, we multiply each term by 100: \[ \left( \frac{\Delta A}{A} \times 100 \right) = \left( \frac{\Delta B}{B} \times 100 \right) + \left( \frac{\Delta C}{C} \times 100 \right) \]
    This can be written more simply as: \[ \Delta A\% = \Delta B\% + \Delta C\% \]
    Now, we substitute the values provided in the question: \[ \Delta B\% = 4\% \] \[ \Delta C\% = 3\% \]
    Calculating the sum: \[ \Delta A\% = 4\% + 3\% = 7\% \]
    Thus, the total percentage error in A is approximately 7%, which corresponds to option A.

    In summary, when two quantities are multiplied, their individual percentage errors are added together to find the total percentage error of the product.
  115. Q115.

    If $A=BC$, with percentage errors $\Delta B\%=1\%$ and $\Delta C\%=2\%$, then $\Delta A\%$ is approximately:

    1. A) $0\%$

    2. B) $2\%$

    3. C) $1\%$

    4. D) $3\%$

    Answer: D

  116. Q116.

    If $A=BC$, with percentage errors $\Delta B\%=3\%$ and $\Delta C\%=1\%$, then $\Delta A\%$ is approximately:

    1. A) $4\%$

    2. B) $0\%$

    3. C) $3\%$

    4. D) $2\%$

    Answer: A

  117. Q117.

    The dimensions of momentum are:

    1. A) $MLT^{-1}$

    2. B) $ML^{2}T^{-2}$

    3. C) $M^{0}LT^{-2}$

    4. D) $M^{1}L^{0}T^{0}$

    Answer: A

  118. Q118.

    The dimensions of pressure are:

    1. A) $ML^{-1}T^{-2}$

    2. B) $MLT^{-2}$

    3. C) $M^{0}L^{1}T^{-1}$

    4. D) $M^{1}L^{2}T^{-3}$

    Answer: A

  119. Q119.

    The dimensions of surface tension are:

    1. A) $MT^{-2}$

    2. B) $ML^{0}T^{-2}$

    3. C) $ML^{0}T^{-1}$

    4. D) $ML^{-1}T^{-2}$

    Answer: D

  120. Q120.

    Dimensional formula of Young’s modulus is the same as:

    1. A) pressure

    2. B) energy

    3. C) force

    4. D) momentum

    Answer: A

  121. Q121.

    In vernier calipers, the zero of vernier to the left of main zero indicates:

    1. A) positive zero error

    2. B) negative zero error

    3. C) no error

    4. D) backlash

    Answer: B

  122. Q122.

    Backlash error in screw gauge is minimized by:

    1. A) tightening the screw more

    2. B) rotating the screw in one direction while taking readings

    3. C) using larger pitch

    4. D) ignoring least count

    Answer: B

  123. Q123.

    Pitch of screw gauge is defined as:

    1. A) distance moved in one complete rotation

    2. B) value of one division on circular scale

    3. C) least count

    4. D) radius of spindle

    Answer: A

  124. Q124.

    A meter rule has least count:

    1. A) $1\ \text{mm}$

    2. B) $0.1\ \text{mm}$

    3. C) $0.01\ \text{mm}$

    4. D) $0.5\ \text{mm}$

    Answer: A

  125. Q125.

    Dimensionless quantities can have units.

    1. A) True

    2. B) False

    3. C) Sometimes

    4. D) Only in CGS

    Answer: B

  126. Q126.

    Two quantities with same dimensions need not be numerically equal.

    1. A) True

    2. B) False

    3. C) Only in SI

    4. D) Only in CGS

    Answer: A

  127. Q127.

    A physical law must be dimensionally homogeneous.

    1. A) True

    2. B) False

    3. C) Not necessary

    4. D) Only empirical laws

    Answer: A

  128. Q128.

    Which instrument is best to measure diameter of a thin wire?

    1. A) Vernier calipers

    2. B) Screw gauge

    3. C) Meter rule

    4. D) Stopwatch

    Answer: B

  129. Q129.

    Which quantity is NOT a base quantity?

    1. A) Electric current

    2. B) Temperature

    3. C) Amount of substance

    4. D) Voltage

    Answer: D

  130. Q130.

    In SI, the unit of temperature is:

    1. A) kelvin

    2. B) degree Celsius

    3. C) fahrenheit

    4. D) rankine

    Answer: A

  131. Q131.

    The unit $\text{N m}$ is equivalent to:

    1. A) joule

    2. B) watt

    3. C) pascal

    4. D) tesla

    Answer: A

  132. Q132.

    Which does NOT affect precision directly?

    1. A) Least count

    2. B) Random error

    3. C) Zero error (uncorrected)

    4. D) Unit conversion

    Answer: D

  133. Q133.

    If $F=ma$, then $[F]$ in base units is:

    1. A) $\text{kg m s}^{-2}$

    2. B) $\text{kg m s}^{-1}$

    3. C) $\text{kg m}^{2}\text{s}^{-2}$

    4. D) $\text{N s}$

    Answer: A

  134. Q134.

    $1\ \text{barn}$ is used to measure:

    1. A) area (nuclear cross-section)

    2. B) energy

    3. C) time

    4. D) volume

    Answer: A

  135. Q135.

    Which is a scalar?

    1. A) Displacement

    2. B) Velocity

    3. C) Speed

    4. D) Momentum

    Answer: C

  136. Q136.

    Which set is correctly matched?

    1. A) Power–$\text{J s}^{-1}$

    2. B) Energy–$\text{N s}$

    3. C) Pressure–$\text{N m}$

    4. D) Force–$\text{J m}$

    Answer: A

  137. Q137.

    The constant $c$ in $E=mc^{2}$ has unit:

    1. A) $\text{m s}^{-1}$

    2. B) $\text{m s}^{-2}$

    3. C) $\text{s}^{-1}$

    4. D) $\text{m}$

    Answer: A

  138. Q138.

    Check the relation $T=2\pi\sqrt{\dfrac{l}{g}}$ for a simple pendulum by dimensions.

    1. A) Consistent

    2. B) Inconsistent

    3. C) Depends on amplitude

    4. D) Depends on mass

    Answer: A

  139. Q139.

    Is $E=\tfrac{1}{2}mv^{2}$ dimensionally consistent?

    1. A) Yes

    2. B) No

    3. C) Gives momentum

    4. D) Gives power

    Answer: A

  140. Q140.

    Is $E=\tfrac{1}{2}mv^{2}$ dimensionally consistent?

    1. A) Yes

    2. B) No

    3. C) Gives momentum

    4. D) Gives power

    Answer: A

  141. Q141.

    Is $E=\tfrac{1}{2}mv^{2}$ dimensionally consistent?

    1. A) Yes

    2. B) No

    3. C) Gives momentum

    4. D) Gives power

    Answer: A

  142. Q142.

    Check the relation $T=2\pi\sqrt{\dfrac{l}{g}}$ for a simple pendulum by dimensions.

    1. A) Consistent

    2. B) Inconsistent

    3. C) Depends on amplitude

    4. D) Depends on mass

    Answer: A

  143. Q143.

    Is $P=Fv$ dimensionally consistent?

    1. A) Yes, gives power

    2. B) No, gives energy

    3. C) No, gives momentum

    4. D) No, gives pressure

    Answer: A

  144. Q144.

    Check the relation $T=2\pi\sqrt{\dfrac{l}{g}}$ for a simple pendulum by dimensions.

    1. A) Consistent

    2. B) Inconsistent

    3. C) Depends on amplitude

    4. D) Depends on mass

    Answer: A

  145. Q145.

    Check the relation $T=2\pi\sqrt{\dfrac{l}{g}}$ for a simple pendulum by dimensions.

    1. A) Consistent

    2. B) Inconsistent

    3. C) Depends on amplitude

    4. D) Depends on mass

    Answer: A

  146. Q146.

    Is $P=Fv$ dimensionally consistent?

    1. A) Yes, gives power

    2. B) No, gives energy

    3. C) No, gives momentum

    4. D) No, gives pressure

    Answer: A

  147. Q147.

    Is $E=\tfrac{1}{2}mv^{2}$ dimensionally consistent?

    1. A) Yes

    2. B) No

    3. C) Gives momentum

    4. D) Gives power

    Answer: A

  148. Q148.

    Is $E=\tfrac{1}{2}mv^{2}$ dimensionally consistent?

    1. A) Yes

    2. B) No

    3. C) Gives momentum

    4. D) Gives power

    Answer: A

  149. Q149.

    Is $P=Fv$ dimensionally consistent?

    1. A) Yes, gives power

    2. B) No, gives energy

    3. C) No, gives momentum

    4. D) No, gives pressure

    Answer: A

  150. Q150.

    Check the relation $T=2\pi\sqrt{\dfrac{l}{g}}$ for a simple pendulum by dimensions.

    1. A) Consistent

    2. B) Inconsistent

    3. C) Depends on amplitude

    4. D) Depends on mass

    Answer: A

  151. Q151.

    Check the relation $T=2\pi\sqrt{\dfrac{l}{g}}$ for a simple pendulum by dimensions.

    1. A) Consistent

    2. B) Inconsistent

    3. C) Depends on amplitude

    4. D) Depends on mass

    Answer: A

  152. Q152.

    Is $E=\tfrac{1}{2}mv^{2}$ dimensionally consistent?

    1. A) Yes

    2. B) No

    3. C) Gives momentum

    4. D) Gives power

    Answer: A

  153. Q153.

    Check by dimensions whether $s=ut+\tfrac{1}{2}at^{2}$ is consistent.

    1. A) Consistent

    2. B) Inconsistent

    3. C) Unit mismatch in $u$

    4. D) Unit mismatch in $a$

    Answer: A

  154. Q154.

    Check by dimensions whether $s=ut+\tfrac{1}{2}at^{2}$ is consistent.

    1. A) Consistent

    2. B) Inconsistent

    3. C) Unit mismatch in $u$

    4. D) Unit mismatch in $a$

    Answer: A

  155. Q155.

    Check by dimensions whether $s=ut+\tfrac{1}{2}at^{2}$ is consistent.

    1. A) Consistent

    2. B) Inconsistent

    3. C) Unit mismatch in $u$

    4. D) Unit mismatch in $a$

    Answer: A

  156. Q156.

    Convert $10\ \text{cm}$ into meters:

    1. A) $0.1$

    2. B) $10.0$

    3. C) $0.01$

    4. D) $1.0$

    Answer: A

  157. Q157.

    Convert $5\ \text{cm}$ into meters:

    1. A) $0.05$

    2. B) $0.005$

    3. C) $0.5$

    4. D) $5.0$

    Answer: A

  158. Q158.

    Convert $0.05\ \text{cm}$ into meters:

    1. A) $0.005$

    2. B) $0.0005$

    3. C) $0.05$

    4. D) $5e-05$

    Answer: B

  159. Q159.

    Convert $5\ \text{cm}$ into meters:

    1. A) $0.05$

    2. B) $0.5$

    3. C) $5.0$

    4. D) $0.005$

    Answer: A

  160. Q160.

    Convert $5\ \text{cm}$ into meters:

    1. A) $5.0$

    2. B) $0.05$

    3. C) $0.5$

    4. D) $0.005$

    Answer: B

  161. Q161.

    Convert $0.2\ \text{cm}$ into meters:

    1. A) $0.2$

    2. B) $0.02$

    3. C) $0.0002$

    4. D) $0.002$

    Answer: D

  162. Q162.

    Convert $0.05\ \text{cm}$ into meters:

    1. A) $0.05$

    2. B) $0.0005$

    3. C) $5e-05$

    4. D) $0.005$

    Answer: B

  163. Q163.

    Convert $50\ \text{cm}$ into meters:

    1. A) $0.05$

    2. B) $50.0$

    3. C) $0.5$

    4. D) $5.0$

    Answer: C

  164. Q164.

    Convert $10\ \text{cm}$ into meters:

    1. A) $10.0$

    2. B) $1.0$

    3. C) $0.01$

    4. D) $0.1$

    Answer: D

  165. Q165.

    Convert $0.2\ \text{cm}$ into meters:

    1. A) $0.0002$

    2. B) $0.02$

    3. C) $0.2$

    4. D) $0.002$

    Answer: D

  166. Q166.

    Convert $50\ \text{cm}$ into meters:

    1. A) $50.0$

    2. B) $0.05$

    3. C) $0.5$

    4. D) $5.0$

    Answer: C

  167. Q167.

    Convert $5\ \text{cm}$ into meters:

    1. A) $5.0$

    2. B) $0.5$

    3. C) $0.005$

    4. D) $0.05$

    Answer: D

  168. Q168.

    Convert $5\ \text{cm}$ into meters:

    1. A) $0.005$

    2. B) $5.0$

    3. C) $0.05$

    4. D) $0.5$

    Answer: C

  169. Q169.

    Convert $0.05\ \text{cm}$ into meters:

    1. A) $0.0005$

    2. B) $5e-05$

    3. C) $0.05$

    4. D) $0.005$

    Answer: A

  170. Q170.

    Convert $20\ \text{cm}$ into meters:

    1. A) $0.2$

    2. B) $20.0$

    3. C) $0.02$

    4. D) $2.0$

    Answer: A

  171. Q171.

    Convert $0.5\ \text{cm}$ into meters:

    1. A) $0.005$

    2. B) $0.5$

    3. C) $0.05$

    4. D) $0.0005$

    Answer: A

  172. Q172.

    Convert $5\ \text{cm}$ into meters:

    1. A) $5.0$

    2. B) $0.005$

    3. C) $0.05$

    4. D) $0.5$

    Answer: C

  173. Q173.

    Convert $100\ \text{cm}$ into meters:

    1. A) $10.0$

    2. B) $100.0$

    3. C) $0.1$

    4. D) $1.0$

    Answer: D

  174. Q174.

    A screw gauge has pitch $0.5\ \text{mm}$ and 50 divisions on the circular scale. Its least count is:

    1. A) $0.5\ \text{mm}$

    2. B) $0.01\ \text{cm}$

    3. C) $50\ \text{mm}$

    4. D) $0.01\ \text{mm}$

    Answer: D

  175. Q175.

    A screw gauge has pitch $0.5\ \text{mm}$ and 50 divisions on the circular scale. Its least count is:

    1. A) $50\ \text{mm}$

    2. B) $0.01\ \text{cm}$

    3. C) $0.5\ \text{mm}$

    4. D) $0.01\ \text{mm}$

    Answer: D

  176. Q176.

    A screw gauge has pitch $0.5\ \text{mm}$ and 100 divisions on the circular scale. Its least count is:

    1. A) $0.5\ \text{mm}$

    2. B) $100\ \text{mm}$

    3. C) $0.005\ \text{mm}$

    4. D) $0.01\ \text{cm}$

    Answer: C

  177. Q177.

    A screw gauge has pitch $1.0\ \text{mm}$ and 50 divisions on the circular scale. Its least count is:

    1. A) $50\ \text{mm}$

    2. B) $0.02\ \text{mm}$

    3. C) $1.0\ \text{mm}$

    4. D) $0.01\ \text{cm}$

    Answer: B

  178. Q178.

    A screw gauge has pitch $0.5\ \text{mm}$ and 50 divisions on the circular scale. Its least count is:

    1. A) $0.01\ \text{mm}$

    2. B) $50\ \text{mm}$

    3. C) $0.5\ \text{mm}$

    4. D) $0.01\ \text{cm}$

    Answer: A

  179. Q179.

    A screw gauge has pitch $1.0\ \text{mm}$ and 100 divisions on the circular scale. Its least count is:

    1. A) $1.0\ \text{mm}$

    2. B) $0.01\ \text{cm}$

    3. C) $100\ \text{mm}$

    4. D) $0.01\ \text{mm}$

    Answer: D

  180. Q180.

    A screw gauge has pitch $0.5\ \text{mm}$ and 100 divisions on the circular scale. Its least count is:

    1. A) $0.5\ \text{mm}$

    2. B) $0.01\ \text{cm}$

    3. C) $0.005\ \text{mm}$

    4. D) $100\ \text{mm}$

    Answer: C

  181. Q181.

    A screw gauge has pitch $0.5\ \text{mm}$ and 50 divisions on the circular scale. Its least count is:

    1. A) $50\ \text{mm}$

    2. B) $0.5\ \text{mm}$

    3. C) $0.01\ \text{mm}$

    4. D) $0.01\ \text{cm}$

    Answer: C

  182. Q182.

    A screw gauge has pitch $0.5\ \text{mm}$ and 100 divisions on the circular scale. Its least count is:

    1. A) $0.5\ \text{mm}$

    2. B) $100\ \text{mm}$

    3. C) $0.005\ \text{mm}$

    4. D) $0.01\ \text{cm}$

    Answer: C

  183. Q183.

    A screw gauge has pitch $1.0\ \text{mm}$ and 50 divisions on the circular scale. Its least count is:

    1. A) $1.0\ \text{mm}$

    2. B) $0.01\ \text{cm}$

    3. C) $50\ \text{mm}$

    4. D) $0.02\ \text{mm}$

    Answer: D

  184. Q184.

    A screw gauge has pitch $0.5\ \text{mm}$ and 50 divisions on the circular scale. Its least count is:

    1. A) $0.01\ \text{mm}$

    2. B) $50\ \text{mm}$

    3. C) $0.01\ \text{cm}$

    4. D) $0.5\ \text{mm}$

    Answer: A

  185. Q185.

    A screw gauge has pitch $1.0\ \text{mm}$ and 50 divisions on the circular scale. Its least count is:

    1. A) $1.0\ \text{mm}$

    2. B) $50\ \text{mm}$

    3. C) $0.02\ \text{mm}$

    4. D) $0.01\ \text{cm}$

    Answer: C

  186. Q186.

    A screw gauge has pitch $1.0\ \text{mm}$ and 50 divisions on the circular scale. Its least count is:

    1. A) $0.02\ \text{mm}$

    2. B) $50\ \text{mm}$

    3. C) $1.0\ \text{mm}$

    4. D) $0.01\ \text{cm}$

    Answer: A

  187. Q187.

    A screw gauge has pitch $1.0\ \text{mm}$ and 100 divisions on the circular scale. Its least count is:

    1. A) $1.0\ \text{mm}$

    2. B) $100\ \text{mm}$

    3. C) $0.01\ \text{mm}$

    4. D) $0.01\ \text{cm}$

    Answer: C

  188. Q188.

    A screw gauge has pitch $1.0\ \text{mm}$ and 50 divisions on the circular scale. Its least count is:

    1. A) $1.0\ \text{mm}$

    2. B) $0.01\ \text{cm}$

    3. C) $50\ \text{mm}$

    4. D) $0.02\ \text{mm}$

    Answer: D

  189. Q189.

    A screw gauge has pitch $1.0\ \text{mm}$ and 50 divisions on the circular scale. Its least count is:

    1. A) $0.01\ \text{cm}$

    2. B) $1.0\ \text{mm}$

    3. C) $50\ \text{mm}$

    4. D) $0.02\ \text{mm}$

    Answer: D

  190. Q190.

    A screw gauge has pitch $0.5\ \text{mm}$ and 50 divisions on the circular scale. Its least count is:

    1. A) $0.5\ \text{mm}$

    2. B) $50\ \text{mm}$

    3. C) $0.01\ \text{cm}$

    4. D) $0.01\ \text{mm}$

    Answer: D

  191. Q191.

    A screw gauge has pitch $0.5\ \text{mm}$ and 50 divisions on the circular scale. Its least count is:

    1. A) $0.5\ \text{mm}$

    2. B) $50\ \text{mm}$

    3. C) $0.01\ \text{mm}$

    4. D) $0.01\ \text{cm}$

    Answer: C

  192. Q192.

    Which is the correct SI unit for quantity $Q_1$ (pressure example)?

    1. A) $\text{N}$

    2. B) $\text{W}$

    3. C) $\text{J}$

    4. D) $\text{Pa}$

    Answer: D

  193. Q193.

    Which one of the following is not the interdisciplinary area of physics?

    1. A) Chemical physics

    2. B) Engineering physics

    3. C) Geophysics

    4. D) Super conductivity

    Answer: D

  194. Q194.

    At present, the numbers of main frontiers of fundamental science are

    1. A) Four

    2. B) Two

    3. C) Three

    4. D) Five

    Answer: C

  195. Q195.

    Light year is

    1. A) Time

    2. B) Year of light

    3. C) Distance

    4. D) Reciprocal of time

    Answer: C

  196. Q196.

    Computer chips are made of

    1. A) Metallic silicon

    2. B) Metalloid silicon

    3. C) Super conducting silicon

    4. D) All of these

    Answer: B

  197. Q197.

    With the help of which one of the following waves big bang theory was proved?

    1. A) X-rays

    2. B) Ultra-violet

    3. C) Radio waves

    4. D) γ-rays

    Answer: C

  198. Q198.

    An ideal standard has two principal characteristics. It is

    1. A) Accessible and variable

    2. B) Inaccessible and variable

    3. C) Inaccessible invariable

    4. D) Accessible and invariable

    Answer: D

  199. Q199.

    Standard kg is an alloy cylinder having

    1. A) 90% Ir, 10% pt

    2. B) 20% pt, 80% Ir

    3. C) 10% Ir, 90% Pt

    4. D) 20% Ir, 80% pt

    Answer: C

  200. Q200.

    Light travels a distance of ______ meters in one second.

    1. A) 1/299, 792, 458

    2. B) 299, 792, 458

    3. C) 299, 792, 548

    4. D) 1/299, 792, 548

    Answer: B

  201. Q201.

    Unit of power in terms of base units

    1. A) watt

    2. B) J/s

    3. C) $kgm^{2}s^{-3}$

    4. D) $kgm^{2}s^{-2}$

    Answer: C

  202. Q202.

    The physical quantity which can be written in terms of just two different SI base units

    1. A) Velocity

    2. B) Area

    3. C) Angular acceleration

    4. D) All

    Answer: A

    To understand which physical quantity is expressed using exactly two different SI base units, we must analyze the units of each option provided.

    1. Velocity:
    Velocity is defined as the rate of change of displacement with respect to time. The formula for velocity is:
    \[ v = \frac{\Delta s}{\Delta t} \]
    The SI base unit for displacement (length) is the meter (m), and the SI base unit for time is the second (s). Therefore, the unit for velocity is \( \text{m/s} \) or \( \text{m} \cdot \text{s}^{-1} \). This quantity clearly involves two different SI base units: the meter and the second.

    2. Area:
    Area is calculated by multiplying two lengths (e.g., length × width). The SI unit for area is square meters (\( \text{m}^2 \)). Although it represents a two-dimensional space, it relies on only one type of SI base unit: the meter.

    3. Angular acceleration:
    Angular acceleration is the rate of change of angular velocity. Its unit is radians per second squared (\( \text{rad/s}^2 \)). In the SI system, the radian is a dimensionless supplementary unit (defined as m/m). Consequently, the only base unit involved in angular acceleration is the second (s), expressed as \( \text{s}^{-2} \). This involves only one type of base unit.

    Conclusion:
    Comparing the options, velocity is the only quantity that requires two distinct base units (length and time) for its definition, whereas area and angular acceleration each rely on only one type of base unit.

    Velocity is the correct choice because its derived unit consists of two distinct SI base units: meters and seconds.
  203. Q203.

    Which of the following pairs have not the same units?

    1. A) Torque and angular momentum

    2. B) Young’s modulus and pressure

    3. C) Torque and work

    4. D) Work and energy

    Answer: A

  204. Q204.

    A precise measurement is one which has

    1. A) High precision

    2. B) Low precision

    3. C) Maximum percentage uncertainty

    4. D) Both B and C

    Answer: A

    In the study of physics and metrology, precision describes how close a series of measurements are to one another. A measurement is said to be precise if it can be reproduced consistently with very little variation between individual readings.

    A measurement with high precision typically has a very small absolute uncertainty. This is often determined by the least count of the measuring instrument used. For example, if we use a vernier caliper with a least count of \( 0.01 \text{ cm} \), it provides a more precise measurement than a standard ruler with a least count of \( 0.1 \text{ cm} \).

    Regarding the provided options:
    - Option A is correct because "precise" is the adjective used to describe a state of high precision.
    - Option B is incorrect as low precision implies a wide scatter of data points.
    - Option C is incorrect because a precise measurement should have the minimum possible uncertainty, not the maximum. High percentage uncertainty usually indicates a lack of accuracy or a measurement where the error is large relative to the total value.

    Therefore, the defining characteristic of a precise measurement is that it exhibits high precision through consistent and repeatable results.

    In summary, a precise measurement is one that shows high consistency and minimal deviation across multiple trials, which is referred to as high precision.
  205. Q205.

    A student takes 100 observations in an experiment. Second time he takes 500 observations in the same experiment. By doing so the possible error becomes

    1. A) 5 times greater

    2. B) 1/5 times lesser

    3. C) 10 times greater

    4. D) 1/10 times lesser

    Answer: B

  206. Q206.

    Density of a liquid is 13.6 g $cm^{-3}$. Its value in SI units is

    1. A) 136.0 kg $m^{-3}$

    2. B) 13600 kg $m^{-3}$

    3. C) 13.6 kg $m^{-3}$

    4. D) 1.36 kg $m^{-3}$

    Answer: B

  207. Q207.

    The density of a cube is measured by measuring its mass and the length of its side. If the maximum errors in the measurement of mass and length are 3% and 2%, respectively, then maximum error in the measurement of density is

    1. A) 1 %

    2. B) 5 %

    3. C) 7 %

    4. D) 9 %

    Answer: D

  208. Q208.

    While measuring acceleration due to gravity by a simple pendulum, a student makes a positive error of 1 % in the length of the pendulum and a negative error of 3 % in the value of time period. The percentage error in the measurement of g is

    1. A) 2 %

    2. B) 4 %

    3. C) 7 %

    4. D) 10 %

    Answer: C

  209. Q209.

    If the error in the measurement of radius of a circle is 1 % then the error in the measurement of its area will be

    1. A) 1.0 %

    2. B) 2 %

    3. C) 1.5 %

    4. D) 3 %

    Answer: B

  210. Q210.

    The radius of a wire is 0.24 mm. Then its area of cross-section by taking significant figures into consideration is

    1. A) 0.19 $mm^{2}$

    2. B) 0.190 $mm^{2}$

    3. C) 0.18 $mm^{2}$

    4. D) 0.180 $mm^{2}$

    Answer: C

  211. Q211.

    The length, breadth and thickness of a block is measured to be 50 cm; 2.0 cm and cm. The percentage error in the measurement of volume is

    1. A) 0.8 %

    2. B) 8 %

    3. C) 10 %

    4. D) 12.5 %

    Answer: A

  212. Q212.

    To reduce the timing uncertainty, it is advisable to

    1. A) Count for smaller number of swing

    2. B) Count for larger number of swing

    3. C) Use a stop watch which is less sensitive

    4. D) Both ‘A’ and ‘C’

    Answer: B

  213. Q213.

    Which one of the following about systematic error is incorrect?

    1. A) It influences all the measurement of a physical quantity equally

    2. B) It produces consistent difference in reading

    3. C) It can be reduced by comparing the instrument with standard instrument

    4. D) It always occurs due to incorrect marking

    Answer: D

  214. Q214.

    In an electrical circuit, the current in a resistor is measured as (2.50 ± 0.05) mA. The resistor is marked as 4.7 Ω ± 2%. What would be the %age uncertainty in power dissipation in resistor?

    1. A) 2%

    2. B) 4%

    3. C) 6%

    4. D) 8%

    Answer: C

  215. Q215.

    Which one of the following measurement is more accurate?

    $M_1$ = 1.0 cm ± 0.1 cm

    $M_2$ = 0.10 cm ± 0.01 cm

    $M_3$ = 0.100 cm ± 0.001 cm

    1. A) $M_1$

    2. B) $M_2$

    3. C) $M_3$

    4. D) All have same accuracy

    Answer: C

  216. Q216.

    The distance $x = x_2 - x_1$ determined by the difference between two separate position measurements $x_1$ = 12.2 ± 0.2 cm and $x_2$ = 16.2 ± 0.1 cm is recorded as

    1. A) 4.0 ± 0.2 cm

    2. B) 4.0 ± 0.1 cm

    3. C) 4.0 ± 0.3 cm

    4. D) 4.0 ± 0.4 cm

    Answer: C

  217. Q217.

    Three students measured the length of the same needle. Student A measured with micrometer screw gauge, B with Vernier calipers and C with meter rod. Which would have greater experimental accuracy of the result?

    1. A) Student A

    2. B) Student B

    3. C) Student C

    4. D) All have same experimental accuracy

    Answer: A

  218. Q218.

    Instrumental error is

    1. A) Random error

    2. B) Systematic error

    3. C) Both

    4. D) None

    Answer: B