149 MCQs for MDCAT Physics. The quiz above checks one question at a time. Every question, option, and saved explanation is on this page.
-
Q1.
Thermal energy naturally flows from a body at
A) lower T to higher T
B) higher T to lower T
C) equal T to equal T
D) depends only on mass
Answer: B
The correct answer is B because thermal energy, commonly referred to as heat, always moves spontaneously from an object with a higher temperature to an object with a lower temperature.
This phenomenon is a fundamental principle of thermodynamics. Temperature \( (T) \) is a measure of the average kinetic energy of the molecules within a substance. When a high-temperature body comes into contact with a low-temperature body, the faster-moving molecules in the warmer object transfer some of their energy to the slower-moving molecules in the cooler object through collisions. This transfer continues until the temperatures equalize, reaching a state of thermal equilibrium.
While it is possible to move heat from a lower temperature to a higher temperature (as seen in refrigerators or heat pumps), this process is not natural or spontaneous; it requires the input of external work. Additionally, while the total mass of an object affects how much total thermal energy it can store, the direction of the energy flow is determined strictly by the temperature difference between the two bodies.
In summary, heat naturally migrates from hotter regions to colder regions until a uniform temperature is achieved.
-
Q2.
Two systems are in thermal equilibrium when
A) they have equal masses
B) no net heat flows between them
C) pressures are equal
D) volumes are equal
Answer: B
Thermal equilibrium is a fundamental concept in thermodynamics that describes the state of a system where its macroscopic properties no longer change over time. When two systems are placed in thermal contact, energy in the form of heat will naturally flow from the system at a higher temperature to the system at a lower temperature.
This process continues until both systems reach the exact same temperature. According to the Zeroth Law of Thermodynamics, if two systems are in thermal equilibrium, there is no net heat flow between them. While microscopic energy exchange still occurs at the molecular level, the rate of energy transfer from the first system to the second is equal to the rate of energy transfer from the second back to the first, resulting in a net exchange of zero.
It is important to distinguish thermal equilibrium from other types of equilibrium:
1. Mechanical Equilibrium: This occurs when the pressures of the systems are equal (Option C), meaning there is no net force.
2. Chemical Equilibrium: This occurs when the chemical potentials are equal, meaning there is no net transfer of matter.
Physical properties like mass (Option A) and volume (Option D) do not need to be equal for thermal equilibrium to exist; for example, a small cup of water and a large lake can be in thermal equilibrium if they are both at \( 20^\circ C \).
Therefore, the defining characteristic of thermal equilibrium is the cessation of net heat transfer due to the equalization of temperatures.
In summary, thermal equilibrium is achieved when two systems reach the same temperature, resulting in no net exchange of thermal energy between them.
-
Q3.
The Zeroth Law of Thermodynamics allows us to define
A) heat
B) temperature
C) work
D) entropy
Answer: B
The Zeroth Law of Thermodynamics states that if two thermodynamic systems are each in thermal equilibrium with a third system, then they are in thermal equilibrium with each other. This principle establishes a transitive relationship that allows us to compare the thermal states of different objects without bringing them into direct contact.
For this relationship to hold true, there must be a common physical property shared by systems in thermal equilibrium. This property is temperature. If two systems have the same temperature, no net heat will flow between them when they are placed in thermal contact.
The Zeroth Law is fundamental because it provides the theoretical justification for the construction and use of thermometers. By using a thermometer as the "third system," we can measure the temperature of various other systems and determine if they would be in equilibrium with one another.
In contrast:
1. Heat and work are modes of energy transfer addressed primarily by the First Law of Thermodynamics.
2. Entropy is a measure of molecular disorder or randomness, which is defined by the Second Law of Thermodynamics.
The Zeroth Law is logically the first step in thermodynamics because it allows us to quantify the thermal state of a system before exploring energy conservation or entropy.
In summary, the Zeroth Law of Thermodynamics is the principle that allows for the formal definition and measurement of temperature.
-
Q4.
When A is in thermal equilibrium with B and B with C, then A and C are
A) never in equilibrium
B) in thermal equilibrium
C) at different temperatures
D) isolated
Answer: B
-
Q5.
Heat is energy transfer due to
A) force
B) temperature difference
C) pressure difference
D) position change
Answer: B
-
Q6.
Work is energy transfer that can be associated with
A) random molecular motion
B) ordered macroscopic motion (force through distance)
C) radiation only
D) conduction only
Answer: B
To understand why Option B is correct, we must distinguish between the two primary modes of energy transfer in physics and thermodynamics: heat and work.
Work is defined as the transfer of energy that occurs when a force acts upon an object to cause displacement. In a thermodynamic sense, work involves the ordered or organized motion of particles or the movement of a macroscopic body. For example, when a gas expands and pushes a piston, the molecules collectively exert a force that moves the piston in a specific direction. This is a clear example of ordered macroscopic motion, which can be expressed by the formula:
\[ W = F \cdot d \]
where \( W \) represents work, \( F \) is the force applied, and \( d \) is the distance over which the force is exerted.
On the other hand, Option A refers to random molecular motion, which is the microscopic definition of heat. Heat transfer involves the chaotic, disorganized movement of atoms and molecules driven by a temperature gradient. Options C and D (radiation and conduction) are specific mechanisms of heat transfer, not work, as they rely on the transfer of thermal energy rather than mechanical force through a distance.
In summary, work is the transfer of energy through organized, large-scale motion resulting from a force acting through a displacement.
-
Q7.
In conduction, thermal energy is transferred by
A) bulk motion of fluid
B) electromagnetic waves
C) molecular collisions within matter
D) chemical reaction
Answer: C
The process of conduction occurs when thermal energy is passed from one particle to another through direct contact. When a substance is heated, its atoms or molecules gain kinetic energy and begin to vibrate or move more rapidly. These energetic particles then collide with neighboring particles, transferring a portion of their energy in the process. This chain reaction allows heat to flow through a material, particularly in solids where particles are closely packed together.
To better understand why the other options are incorrect, consider the following definitions of heat transfer:
1. Bulk motion of fluid: This describes convection. In convection, heat is carried by the actual movement of warmed matter, such as air or water currents.
2. Electromagnetic waves: This describes radiation. Unlike conduction, radiation does not require a physical medium and can transfer energy through the vacuum of space.
3. Chemical reaction: While chemical reactions can be exothermic (releasing heat) or endothermic (absorbing heat), they represent a transformation of energy rather than a physical mechanism for transferring thermal energy between substances.
Because conduction relies on the physical interaction and microscopic bumping of particles, molecular collisions within matter is the correct description of the process.
In summary, conduction is the transfer of thermal energy through the direct collision of particles within a medium.
-
Q8.
In convection, heat is carried mainly by
A) photons
B) moving fluid
C) stationary atoms
D) vacuum
Answer: B
-
Q9.
Thermal radiation requires
A) a medium
B) vacuum only
C) no medium
D) solid contact
Answer: C
Thermal radiation is the process by which heat is emitted from a body in the form of electromagnetic waves. Unlike conduction and convection, which depend on the presence of matter to transfer energy, radiation is unique because it does not rely on any material particles.
In conduction, heat moves through solids via direct molecular contact. In convection, heat is carried by the movement of liquids or gases. However, thermal radiation consists of electromagnetic waves, primarily in the infrared spectrum, that can travel through the emptiness of space. This is why we are able to feel the heat from the Sun even though there is a vast vacuum between the Sun and the Earth.
While radiation can pass through certain media, such as air or glass, the fundamental requirement for its propagation is simply the emission of energy from a source. Because electromagnetic waves do not need a physical substance to vibrate or move, a medium is not a requirement for the transfer to occur. According to the Stefan-Boltzmann law, the power radiated is proportional to the fourth power of the absolute temperature, expressed as:
\[ P = \sigma A T^4 \]
This formula demonstrates that the energy emission depends on the properties of the object itself rather than the surrounding environment.
In summary, thermal radiation does not require a medium because it travels as electromagnetic waves that can propagate through a vacuum.
-
Q10.
Two objects at same temperature have
A) same internal energy
B) thermal equilibrium (no net heat flow)
C) same mass
D) same volume
Answer: B
Okay, let's break down why option B, "thermal equilibrium (no net heat flow)," is the correct answer.
Here's the explanation:
**Understanding Temperature and Thermal Equilibrium**
Temperature is a measure of the *average* kinetic energy of the particles (atoms or molecules) within a substance. When two objects are at the *same* temperature, it means their particles, on average, have the same kinetic energy.
**What is Thermal Equilibrium?**
Thermal equilibrium is a state where two or more objects (or systems) are in contact and there is *no net* transfer of heat between them. This happens when they are at the same temperature. Heat flows from a hotter object to a colder object until they reach the same temperature, at which point they are in thermal equilibrium.
**Why the Other Options are Incorrect**
Let's look at why the other options are wrong:
* **A) same internal energy:** Internal energy is the *total* energy of a system, which includes both kinetic energy (related to temperature) and potential energy (related to the positions of the molecules). Two objects can be at the same temperature but have different internal energies if they have different masses or different types of molecules. For example, a small cup of boiling water and a large swimming pool of lukewarm water could both be at 100°C, but the swimming pool has vastly more internal energy.
* **C) same mass:** Temperature has nothing to do with mass. Objects of any mass can be at the same temperature.
* **D) same volume:** Similarly, volume is independent of temperature. Objects of different volumes can be at the same temperature.
**Therefore...**
Since two objects at the same temperature will not have a net transfer of heat between them, they are in thermal equilibrium. This is the defining characteristic of objects at the same temperature.
**In summary:** The key concept here is that equal temperatures imply no net heat flow, which is the definition of thermal equilibrium.
-
Q11.
Thermal contact means systems can
A) exchange heat
B) exchange only work
C) exchange matter
D) not interact
Answer: A
-
Q12.
Temperature is a measure of
A) total internal energy
B) average random kinetic energy per particle
C) momentum
D) mass density
Answer: B
To understand why temperature is defined as the average random kinetic energy per particle, we must look at the behavior of matter on a microscopic scale. All matter is composed of atoms and molecules that are in constant, random motion.
Reasoning:
Temperature is a macroscopic property that we perceive as hot or cold, but at the molecular level, it is a direct reflection of how fast the particles in a substance are moving. According to the kinetic-molecular theory, the faster the particles move, the higher the temperature of the substance.
Option A is incorrect because total internal energy refers to the sum of all kinetic and potential energies of all particles in a system. While temperature is related to internal energy, it does not account for the total amount of substance. For example, a large lake and a small cup of water can be at the same temperature, but the lake has much more total internal energy because it contains many more particles.
Option B is the correct choice. Temperature specifically measures the average kinetic energy of the individual particles, regardless of how many particles there are. This relationship is mathematically expressed for an ideal gas using the following formula:
\[ KE_{avg} = \frac{3}{2} k_B T \]
In this equation, \( KE_{avg} \) represents the average kinetic energy per particle, \( k_B \) is the Boltzmann constant, and \( T \) is the absolute temperature in Kelvin. This shows that temperature is directly proportional to the average kinetic energy.
Option C (momentum) and Option D (mass density) are incorrect because they describe different physical properties. Momentum involves the product of mass and velocity in a specific direction, while density describes how much mass is contained in a given volume; neither serves as a definition for the thermal state of a substance.
In summary, temperature provides a way to quantify the intensity of the random motion of particles within a substance, representing the average kinetic energy found in each particle.
-
Q13.
Thermal equilibrium implies
A) equality of pressure
B) equality of temperature
C) equality of volume
D) equality of density
Answer: B
-
Q14.
Units of heat in SI are
A) calorie
B) joule
C) watt
D) newton
Answer: B
-
Q15.
One calorie is approximately
A) 1 J
B) 4.186 J
C) 0.4186 J
D) 41.86 J
Answer: B
-
Q16.
Internal energy of an ideal gas depends on
A) pressure only
B) temperature only
C) volume only
D) temperature and volume
Answer: B
-
Q17.
The First Law of Thermodynamics is
A) Q = W
B) ?U = Q - W
C) ?U = W - Q
D) Q = ?U - W
Answer: B
The First Law of Thermodynamics is a fundamental principle in physics that represents the law of conservation of energy. It states that energy cannot be created or destroyed, only transformed from one form to another within a system and its surroundings.
In a thermodynamic process, when heat energy (denoted as \( Q \)) is added to a system, that energy is used for two purposes: it increases the internal energy of the system (denoted as \( \Delta U \)) and it allows the system to perform external work (denoted as \( W \)). The mathematical relationship is expressed as:
\[ Q = \Delta U + W \]
To isolate the change in internal energy, we rearrange the equation as follows:
\[ \Delta U = Q - W \]
In this context:
- \( \Delta U \) (often represented as ?U in text-based formats) is the change in internal energy.
- \( Q \) is the net heat added to the system.
- \( W \) is the net work done by the system on its surroundings.
Therefore, Option B is the correct mathematical statement of the law, showing that the internal energy of a system increases by the amount of heat added and decreases by the amount of work the system performs.
This law serves as a definitive energy balance equation for any thermodynamic cycle or process.
-
Q18.
In the sign convention used in physics here, W is positive when
A) work is done on the gas
B) work is done by the gas
C) no work is done
D) volume decreases
Answer: B
In the study of thermodynamics, the sign convention for work (\( W \)) depends on whether the perspective is that of physics or chemistry. In the standard physics convention, the focus is often on heat engines, where the goal is to extract useful work from a system.
In this specific convention, work is defined as positive when it is done by the gas (the system) on its surroundings. This typically happens during expansion, where the gas pushes against a piston or boundary. The formula for work done by a gas at constant pressure is expressed as:
\[ W = P \Delta V \]
When the gas expands, the change in volume (\( \Delta V \)) is positive, which results in a positive value for \( W \). This convention is used in the First Law of Thermodynamics when written as:
\[ \Delta U = Q - W \]
In this form, a positive \( W \) indicates that energy is leaving the system in the form of work done on the environment, thereby reducing the internal energy (\( \Delta U \)) unless heat (\( Q \)) is added.
If work were done on the gas (compression), the volume would decrease, making \( \Delta V \) negative, and the work would be considered negative in this convention. Therefore, the correct choice is that work is positive when the gas performs work on its surroundings.
Summary: In the physics sign convention, work is considered positive when the system expands and does work on its environment.
-
Q19.
For isochoric (constant volume) process, work W equals
A) P?V
B) zero
C) nRT ln(V2/V1)
D) ?PdV ? 0
Answer: B
In thermodynamics, an isochoric process is defined as a process where the volume of the system remains constant. This means that the initial volume \( V_1 \) is equal to the final volume \( V_2 \), resulting in a change in volume \( \Delta V = 0 \).
The mathematical expression for the work done (\( W \)) by a gas during a thermodynamic process is given by the integral of pressure (\( P \)) with respect to volume (\( V \)):
\[ W = \int_{V_1}^{V_2} P \, dV \]
Because the volume does not change in an isochoric process, the differential change in volume \( dV \) is equal to zero. When we substitute this into the equation, the entire expression for work becomes zero:
\[ W = \int P \cdot 0 = 0 \]
From a physical perspective, work is performed when a force causes a displacement. In a gas system, this typically involves the expansion or compression of the container (moving boundaries). If the volume is fixed, there is no displacement of the system's boundaries, and therefore, no mechanical work is performed on the surroundings.
Other options like \( P\Delta V \) (Option A) represent work at constant pressure, and \( nRT \ln(V_2/V_1) \) (Option C) represents work during an isothermal process. For the isochoric case, the only correct value is zero.
Summary: Since work requires a change in volume and an isochoric process occurs at constant volume, the total work done is always zero.
-
Q20.
For isothermal expansion of ideal gas, ?U equals
A) positive
B) negative
C) zero
D) infinite
Answer: C
To understand why the change in internal energy (represented as \(\Delta U\)) is zero during the isothermal expansion of an ideal gas, we must look at the fundamental properties of ideal gases and the definition of the process involved.
1. Definition of an Isothermal Process:
The term isothermal refers to a thermodynamic process in which the temperature of the system remains constant throughout. Mathematically, this means:
\[ \Delta T = 0 \]
2. Internal Energy of an Ideal Gas:
According to the kinetic molecular theory, the internal energy (\(U\)) of an ideal gas is a function of its absolute temperature only. This is because ideal gas particles are assumed to have no intermolecular forces of attraction or repulsion. Therefore, there is no internal potential energy, and the internal energy consists entirely of the kinetic energy of the molecules, which is directly proportional to the temperature.
3. The Mathematical Relationship:
The change in internal energy for an ideal gas can be expressed by the following formula:
\[ \Delta U = n C_v \Delta T \]
Where:
\(n\) = number of moles of the gas
\(C_v\) = molar heat capacity at constant volume
\(\Delta T\) = change in temperature
Since the process is isothermal, the change in temperature (\(\Delta T\)) is zero. Substituting this into the equation:
\[ \Delta U = n C_v (0) = 0 \]
4. Conclusion:
Regardless of whether the gas is expanding or being compressed, as long as the process is isothermal and the gas behaves ideally, the internal energy does not change. Any heat added to the system during expansion is exactly balanced by the work done by the gas on its surroundings, keeping the internal energy constant.
Summary: For an isothermal expansion of an ideal gas, the change in internal energy is zero because the internal energy of an ideal gas depends solely on temperature, which remains constant during the process.
-
Q21.
Work in isothermal expansion of ideal gas (n moles) is
A) W = nR(T2-T1)
B) W = nRT ln(V2/V1)
C) W = P?V ˜ 0
D) W = 0
Answer: B
-
Q22.
For adiabatic process of ideal gas, heat exchanged Q is
A) nCp?T
B) nCv?T
C) zero
D) nR ln(V2/V1)
Answer: C
The term adiabatic refers to a specific type of thermodynamic process in which no heat is transferred into or out of the system.
In thermodynamics, the heat exchanged between a system and its surroundings is represented by the symbol \( Q \). By definition, an adiabatic process occurs without the exchange of heat or matter. This usually happens when the system is perfectly insulated or when the process occurs so rapidly that there is no time for heat to flow.
According to the First Law of Thermodynamics, the relationship between internal energy (\( \Delta U \)), heat (\( Q \)), and work (\( W \)) is expressed as:
\[ \Delta U = Q - W \]
For an adiabatic process, since there is no heat exchange, we set:
\[ Q = 0 \]
Let us briefly look at why the other options are incorrect for an adiabatic process:
- Option A: \( nC_p \Delta T \) represents the heat exchanged during a process occurring at constant pressure.
- Option B: \( nC_v \Delta T \) represents the heat exchanged during a process occurring at constant volume, which is also equal to the change in internal energy (\( \Delta U \)).
- Option D: \( nRT \ln(V_2/V_1) \) represents the heat exchanged (and work done) during an isothermal process (where temperature remains constant).
Since the defining characteristic of an adiabatic process is the total lack of heat transfer, the value of \( Q \) must be zero.
In summary, an adiabatic process is defined by the absence of heat exchange with the surroundings, meaning \( Q \) is always zero.
-
Q23.
In a quasistatic process, the system
A) is always far from equilibrium
B) passes through a succession of equilibrium states
C) exchanges matter continuously
D) must be adiabatic
Answer: B
A quasistatic process is an idealized thermodynamic process that occurs at an infinitely slow rate. The word quasistatic is derived from the Latin quasi, meaning as if, and the Greek statikos, meaning at rest. This implies that the process happens so slowly that the system remains almost at rest or in equilibrium throughout the entire duration.
In a real-world scenario, when a system changes from one state to another, there are often gradients in pressure or temperature that cause the system to be out of equilibrium. However, in a quasistatic process, the external conditions are changed by such tiny increments that the system has ample time to redistribute its energy and maintain internal equilibrium. Consequently, the system is described as passing through a continuous succession of equilibrium states.
This concept is vital in thermodynamics because it allows us to define state variables, such as pressure \( P \) and temperature \( T \), at every point along the process path. For example, the work done by a gas can be calculated using the integral:
\[ W = \int P \, dV \]
This calculation is only valid if the pressure is uniform and well-defined at every stage, which is a defining characteristic of a quasistatic process.
To clarify why the other options are incorrect:
1. Option A: A system far from equilibrium characterizes a non-quasistatic or "sudden" process.
2. Option C: The exchange of matter refers to whether a system is open or closed, which is independent of whether the process is quasistatic.
3. Option D: A quasistatic process does not have to be adiabatic; it can be isothermal (constant temperature), isobaric (constant pressure), or involve heat exchange.
In summary, a quasistatic process is defined by its infinitely slow progression, which allows the system to remain in a continuous series of equilibrium states throughout the transformation.
-
Q24.
Specific heat capacity at constant volume for ideal monoatomic gas equals
A) (3/2)R per mole
B) (5/2)R per mole
C) R per mole
D) 0
Answer: A
To understand the specific heat capacity of an ideal monoatomic gas, we must first look at its degrees of freedom. A monoatomic gas consists of single atoms (such as Helium or Argon) that are treated as point masses. These atoms can move freely in three-dimensional space along the x, y, and z axes. Therefore, a monoatomic gas has 3 degrees of freedom (\( f = 3 \)), all of which are translational.
According to the law of equipartition of energy, each degree of freedom contributes \( \frac{1}{2}RT \) to the internal energy (\( U \)) per mole of an ideal gas, where \( R \) is the universal gas constant and \( T \) is the absolute temperature.
For a monoatomic gas with 3 degrees of freedom, the total internal energy per mole is calculated as:
\[ U = \frac{3}{2}RT \]
The molar specific heat capacity at constant volume (\( C_v \)) is defined as the change in internal energy with respect to temperature at a constant volume. This is mathematically expressed as the derivative of internal energy:
\[ C_v = \frac{dU}{dT} \]
By substituting the expression for internal energy into this formula, we get:
\[ C_v = \frac{d}{dT} \left( \frac{3}{2}RT \right) \]
\[ C_v = \frac{3}{2}R \]
This result shows that for every mole of a monoatomic gas, the energy required to raise its temperature by one Kelvin at constant volume is exactly \( \frac{3}{2}R \). In contrast, diatomic gases have more degrees of freedom (including rotational ones), leading to higher values like \( \frac{5}{2}R \).
Summary: The specific heat capacity at constant volume for an ideal monoatomic gas is \( \frac{3}{2}R \) because it possesses three translational degrees of freedom.
-
Q25.
For an ideal gas, Cp - Cv equals
A) 0
B) R
C) 2R
D) R/2
Answer: B
-
Q26.
Ratio ? = Cp/Cv for ideal monoatomic gas is approximately
A) 1.33
B) 1.40
C) 1.67
D) 1.00
Answer: C
-
Q27.
Work done in a PV diagram equals
A) area under T–V curve
B) area under P–V curve
C) slope of P–V
D) area under P–T curve
Answer: B
-
Q28.
State variables are
A) Q and W
B) P, V, T, U
C) Q only
D) W only
Answer: B
-
Q29.
Heat and work are
A) path functions
B) state functions
C) constants
D) intensive properties
Answer: A
In thermodynamics, heat (\( Q \)) and work (\( W \)) are defined as energy in transit. They are not properties that a system "possesses" while at rest; instead, they represent the energy moving across the boundary of a system during a change of state.
The primary reason these are classified as path functions is that the total amount of heat transferred or work performed depends entirely on the specific process or "path" taken to get from the initial state to the final state. For example, if a gas expands from an initial volume to a final volume, the work done will vary significantly depending on whether the expansion occurs at a constant temperature (isothermal), a constant pressure (isobaric), or without any heat exchange (adiabatic).
This is mathematically represented by the fact that the differentials for heat and work, \( \delta Q \) and \( \delta W \), are inexact differentials. This distinguishes them from state functions, such as internal energy (\( U \)), pressure (\( P \)), or temperature (\( T \)), which depend only on the current equilibrium state of the system and not on its history.
The relationship between these concepts is illustrated by the First Law of Thermodynamics:
\[ \Delta U = Q - W \]
In this equation, \( \Delta U \) (the change in internal energy) is a state function and remains the same for any path between two specific points. However, the individual values of \( Q \) and \( W \) will change depending on the route taken, confirming that they are path-dependent quantities.
In summary, heat and work are path functions because their values are determined by the specific trajectory or process followed during a thermodynamic transition.
-
Q30.
Mechanical equivalent of heat J is numerically about
A) 1.00 J/cal
B) 4.186 J/cal
C) 0.239 J/cal
D) 10.0 J/cal
Answer: B
-
Q31.
Heat required to raise temperature of mass m by ?T is
A) Q = m?T/c
B) Q = mc?T
C) Q = c/?T
D) Q = m/?T
Answer: B
-
Q32.
Specific heat capacity SI unit is
A) J kg^-1
B) J kg^-1 K^-1
C) J K
D) W m^-1 K^-1
Answer: B
-
Q33.
Latent heat is heat absorbed/released at
A) constant temperature during phase change
B) variable temperature
C) zero pressure
D) high velocity
Answer: A
-
Q34.
Numerical: 0.50 kg water (c=4200 J kg^-1 K^-1) heated by 10 K. Heat Q˜
A) 2.1 kJ
B) 21 kJ
C) 210 kJ
D) 0.21 kJ
Answer: B
-
Q35.
Numerical: 200 g copper (c=390 J kg^-1 K^-1) cools by 30 K. Heat lost˜
A) 2.34 kJ
B) 0.78 kJ
C) 23.4 kJ
D) 0.234 kJ
Answer: D
To calculate the heat lost by the copper, we use the fundamental formula for specific heat capacity:
\[ Q = m \cdot c \cdot \Delta T \]
Where:
Q is the heat energy lost (in Joules),
m is the mass of the substance (in kilograms),
c is the specific heat capacity (in \( \text{J kg}^{-1} \text{ K}^{-1} \)), and
\( \Delta T \) is the change in temperature (in Kelvin).
Step 1: Convert the mass to kilograms
The mass is given as 200 g. Since the specific heat capacity is provided in terms of kilograms, we must convert the mass to the standard SI unit:
\[ m = 200 \text{ g} = \frac{200}{1000} \text{ kg} = 0.2 \text{ kg} \]
Step 2: Substitute the values into the formula
Using the values provided in the question:
- \( m = 0.2 \text{ kg} \)
- \( c = 390 \text{ J kg}^{-1} \text{ K}^{-1} \)
- \( \Delta T = 30 \text{ K} \)
\[ Q = 0.2 \times 390 \times 30 \]
Step 3: Perform the calculation
First, multiply the mass by the specific heat:
\[ 0.2 \times 390 = 78 \]
Next, multiply that result by the temperature change:
\[ 78 \times 30 = 2340 \text{ Joules} \]
Step 4: Convert Joules to kilojoules
The options are provided in kilojoules (kJ). To convert from Joules to kilojoules, divide by 1,000:
\[ Q = \frac{2340}{1000} = 2.34 \text{ kJ} \]
Conclusion:
Based on the numerical values provided (200 g, 390 \( c \), and 30 K), the calculated heat loss is 2.34 kJ. While the provided answer key indicates D (0.234 kJ), the mathematical derivation using these specific inputs results in 2.34 kJ (Option A). If the intended answer was 0.234 kJ, the mass in the problem would likely have been 20 g instead of 200 g.
By applying the heat energy formula and ensuring unit consistency, we find that the copper loses 2.34 kJ of energy.
-
Q36.
Numerical: Ice at 0°C melts. Heat required is
A) mLf
B) mc?T
C) mLv
D) zero
Answer: A
-
Q37.
Numerical: 100 g ice at 0°C (Lf=334 kJ/kg) melts completely. Q˜
A) 3.34 kJ
B) 33.4 kJ
C) 0.334 kJ
D) 334 kJ
Answer: A
To determine the amount of heat energy required to melt the ice, we use the formula for latent heat of fusion, which applies when a substance changes phase at a constant temperature.
The formula is:
\[ Q = m \cdot L_{f} \]
Where:
- \( Q \) is the total heat energy required.
- \( m \) is the mass of the substance.
- \( L_{f} \) is the specific latent heat of fusion for the substance.
Step 1: Convert the mass to kilograms
The specific latent heat (\( L_{f} \)) is provided in kilojoules per kilogram (kJ/kg). Therefore, we must convert the mass of the ice from grams (g) to kilograms (kg) to keep the units consistent:
\[ m = 100 \text{ g} = \frac{100}{1000} \text{ kg} = 0.1 \text{ kg} \]
Step 2: Calculate the heat energy
Now, substitute the mass and the latent heat of fusion into the formula:
\[ Q = 0.1 \text{ kg} \times 334 \text{ kJ/kg} \]
\[ Q = 33.4 \text{ kJ} \]
Step 3: Evaluate the options
The calculated value is 33.4 kJ. Looking at the provided options:
A) 3.34 kJ
B) 33.4 kJ
C) 0.334 kJ
D) 334 kJ
The mathematical result is 33.4 kJ, which matches Option B. If the answer key indicates Option A, it is likely a typographical error regarding the decimal point in the source material, as the standard calculation for 100g of ice results in 33.4 kJ.
By multiplying the mass of 0.1 kg by the latent heat of 334 kJ/kg, we find that the total heat required to melt the ice is 33.4 kJ.
-
Q38.
Calorimetry assumes
A) no heat loss to surroundings
B) heat lost = 0
C) mass lost = 0
D) temperature constant
Answer: A
-
Q39.
Numerical: 0.2 kg aluminum (c=900) at 80°C dropped into 0.3 kg water at 20°C. Final T (no loss) ˜
A) 26°C
B) 30°C
C) 34°C
D) 40°C
Answer: C
To find the final temperature (\( T_f \)) of the mixture, we apply the Principle of Calorimetry, which states that the heat lost by the hot object is equal to the heat gained by the cold object in an isolated system.
1. Identify the given parameters:
For Aluminum (Hot Object):
Mass (\( m_1 \)) = 0.2 kg
Specific heat (\( c_1 \)) = 900 J/kg°C
Initial temperature (\( T_1 \)) = 80°C
For Water (Cold Object):
Mass (\( m_2 \)) = 0.3 kg
Specific heat (\( c_2 \)) = 4186 J/kg°C (standard value for water)
Initial temperature (\( T_2 \)) = 20°C
2. Set up the Heat Balance Equation:
The formula for heat exchange is \( Q = m \cdot c \cdot \Delta T \). According to the principle of conservation of energy:
\[ Q_{lost} = Q_{gained} \]
\[ m_1 \cdot c_1 \cdot (T_1 - T_f) = m_2 \cdot c_2 \cdot (T_f - T_2) \]
3. Substitute the values and solve:
\[ 0.2 \cdot 900 \cdot (80 - T_f) = 0.3 \cdot 4186 \cdot (T_f - 20) \]
\[ 180 \cdot (80 - T_f) = 1255.8 \cdot (T_f - 20) \]
\[ 14400 - 180T_f = 1255.8T_f - 25116 \]
\[ 14400 + 25116 = 1255.8T_f + 180T_f \]
\[ 39516 = 1435.8T_f \]
\[ T_f = \frac{39516}{1435.8} \approx 27.5°C \]
4. Analysis of the Options:
Using the standard values provided in the question, the result is approximately 27.5°C. However, the designated correct answer is 34°C (Option C). This discrepancy often occurs in physics problems if the mass values were intended to be different. For instance, if the mass of Aluminum was 0.3 kg and the mass of Water was 0.2 kg, the calculation would be:
\[ 0.3 \cdot 900 \cdot (80 - T_f) = 0.2 \cdot 4186 \cdot (T_f - 20) \]
\[ 270 \cdot (80 - T_f) = 837.2 \cdot (T_f - 20) \]
\[ 21600 - 270T_f = 837.2T_f - 16744 \]
\[ 38344 = 1107.2T_f \]
\[ T_f \approx 34.6°C \]
This result aligns with the provided answer C. In either case, the methodology remains the same: equating the energy lost by the warmer substance to the energy gained by the cooler substance.
By using the principle of heat exchange, we calculate the point of thermal equilibrium between the aluminum and the water.
-
Q40.
Numerical: 500 g water at 30°C receives 21 kJ. Rise in T˜
A) 5 K
B) 10 K
C) 20 K
D) 100 K
Answer: B
-
Q41.
Heat capacity of a body is
A) heat per mole
B) heat required per unit temperature rise
C) m/c
D) c/m
Answer: B
-
Q42.
Mixture problems use principle
A) energy not conserved
B) heat lost by hot = heat gained by cold
C) masses equal
D) volumes equal
Answer: B
-
Q43.
Numerical: 0.4 kg copper (390) at 200°C into 0.5 kg water at 20°C. Final T˜
A) 28°C
B) 34°C
C) 40°C
D) 50°C
Answer: B
-
Q44.
Numerical: 1.0 kg water at 100°C converted to steam (Lv=2.26 MJ/kg). Heat˜
A) 2.26 kJ
B) 22.6 kJ
C) 226 kJ
D) 2.26 MJ
Answer: D
-
Q45.
Work at constant pressure is
A) W = P?V
B) W = ?U
C) W = 0
D) W = nR?T
Answer: A
-
Q46.
For an ideal gas, ?U equals
A) nCv?T
B) nCp?T
C) nR ln(V2/V1)
D) P?V
Answer: A
-
Q47.
Numerical: 2.0 mol ideal monoatomic gas heated at constant V by 50 K. ?U˜
A) 2×(3/2)R×50
B) 2×(5/2)R×50
C) 2×R×50
D) 0
Answer: A
-
Q48.
Numerical: In above, heat Q equals
A) nCp?T
B) nCv?T
C) 0
D) P?V
Answer: B
-
Q49.
Numerical: Gas expands isothermally from V1 to 2V1 at T=300 K, n=1 mol. Work W˜
A) nRT ln2
B) nRT
C) 2nRT
D) 0
Answer: A
Okay, let's break down why the correct answer is A) nRT ln2. This question deals with the work done during an isothermal expansion of a gas. Here's the explanation:
**Understanding Isothermal Expansion**
First, let's clarify what "isothermal" means. "Isothermal" means the temperature (T) of the system remains constant throughout the process. This is a crucial piece of information.
**Work Done in an Isothermal Process**
The work (W) done by a gas during a reversible isothermal process is given by the following formula:
\[
W = - \int_{V_1}^{V_2} P \, dV
\]
Where:
* `W` is the work done by the gas.
* `P` is the pressure of the gas.
* `V_1` is the initial volume.
* `V_2` is the final volume.
For an ideal gas, we can use the ideal gas law to relate pressure and volume at constant temperature:
\[
PV = nRT
\]
Where:
* `n` is the number of moles of the gas.
* `R` is the ideal gas constant.
* `T` is the temperature (constant in this case).
We can rearrange the ideal gas law to express pressure in terms of volume:
\[
P = \frac{nRT}{V}
\]
Now, substitute this expression for `P` into the work equation:
\[
W = - \int_{V_1}^{V_2} \frac{nRT}{V} \, dV
\]
Since `n`, `R`, and `T` are constants, we can take them out of the integral:
\[
W = -nRT \int_{V_1}^{V_2} \frac{1}{V} \, dV
\]
The integral of 1/V is ln|V|:
\[
W = -nRT \left[ \ln|V| \right]_{V_1}^{V_2}
\]
Now, evaluate the definite integral:
\[
W = -nRT \left( \ln(V_2) - \ln(V_1) \right)
\]
Using the logarithm property `ln(a) - ln(b) = ln(a/b)`:
\[
W = -nRT \ln\left(\frac{V_2}{V_1}\right)
\]
**Applying the Given Information**
The problem states that the gas expands from `V1` to `2V1`. Therefore, `V2 = 2V1`. Substitute this into the equation:
\[
W = -nRT \ln\left(\frac{2V_1}{V_1}\right)
\]
\[
W = -nRT \ln(2)
\]
The question asks for the work `W~`, which is the work done *by* the gas. The negative sign indicates work done *on* the gas. Since we want the work done *by* the gas, we take the absolute value (or negate the negative sign):
\[
W = nRT \ln(2)
\]
**Conclusion**
Therefore, the work done during the isothermal expansion is `nRT ln(2)`, which corresponds to option A. The other options are incorrect because they don't account for the logarithmic relationship between work and volume change in an isothermal process.
I hope this explanation is clear and helpful! Let me know if you have any other questions.
-
Q50.
Numerical: For adiabatic expansion of ideal gas with ?=5/3, PV^?=
A) constant
B) zero
C) proportional to T
D) proportional to V
Answer: A
-
Q51.
Numerical: 1 mol ideal gas at 300 K compressed isothermally to half volume. W by gas˜
A) +nRT ln2
B) -nRT ln2
C) +2nRT
D) 0
Answer: B
-
Q52.
Numerical: At constant P=1.0×10^5 Pa, ?V=0.010 m^3. Work by gas˜
A) 1000 J
B) 100 J
C) 10 J
D) 1 J
Answer: A
-
Q53.
Numerical: A system has Q=500 J and W=200 J (by system). ?U=
A) 700 J
B) 300 J
C) 500 J
D) -300 J
Answer: B
-
Q54.
Numerical: If ?U=-100 J and W=+250 J (by system), then Q=
A) 150 J
B) -350 J
C) 350 J
D) -150 J
Answer: A
-
Q55.
Numerical: 0.5 mol monoatomic ideal gas: ?T=60 K. ?U˜
A) (3/2)nR?T
B) (5/2)nR?T
C) nR?T
D) 0
Answer: A
To find the change in internal energy (\(\Delta U\)) for an ideal gas, we must look at the relationship between temperature, degrees of freedom, and the amount of substance. According to the kinetic theory of gases, the internal energy of an ideal gas depends solely on its temperature.
For a monoatomic ideal gas, the atoms are treated as point masses that only have translational kinetic energy. This results in 3 degrees of freedom (\(f = 3\)). The molar specific heat capacity at constant volume (\(C_v\)) for such a gas is defined as:
\[ C_v = \frac{f}{2}R = \frac{3}{2}R \]
where \(R\) is the universal gas constant.
The formula for the change in internal energy is given by:
\[ \Delta U = n C_v \Delta T \]
By substituting the value of \(C_v\) for a monoatomic gas into the formula, we obtain:
\[ \Delta U = n \left( \frac{3}{2}R \right) \Delta T \]
\[ \Delta U = \frac{3}{2} n R \Delta T \]
In the context of the provided options:
Option A: \(\frac{3}{2} n R \Delta T\) correctly identifies the formula for a monoatomic gas.
Option B: \(\frac{5}{2} n R \Delta T\) would be the formula for a diatomic gas (which has 5 degrees of freedom at room temperature).
Option C: \(n R \Delta T\) represents the work done during an isobaric expansion (\(P\Delta V\)), not the internal energy change.
Option D: 0 would only be correct if the process were isothermal (\(\Delta T = 0\)), but here \(\Delta T = 60\) K.
Even though specific values for \(n\) (0.5 mol) and \(\Delta T\) (60 K) are provided, the options are listed as general algebraic expressions, and Option A is the mathematically correct form for a monoatomic gas.
The internal energy change of a monoatomic gas is determined by its three translational degrees of freedom, leading to the expression \(\frac{3}{2} n R \Delta T\).
-
Q56.
In an isobaric heating, Q equals
A) nCp?T
B) nCv?T
C) 0
D) nR?T
Answer: A
-
Q57.
Numerical: 1 mol ideal gas heated isobarically ?T=40 K, Cp=(5/2)R. Q˜
A) 40R
B) 60R
C) 100R
D) (5/2)R
Answer: A
Okay, let's break down this thermodynamics problem step-by-step. The question asks us to find the heat added (Q) to 1 mole of an ideal gas during an isobaric (constant pressure) process where the temperature changes by ΔT = 40 K, and the molar heat capacity at constant pressure (Cp) is (5/2)R.
Here's the reasoning and the calculation:
**Understanding Isobaric Processes and Heat**
In an isobaric process, the pressure remains constant. The heat added to a system is related to the change in internal energy (ΔU) and the work done (W) by the system through the First Law of Thermodynamics:
\[
\Delta U + W = Q
\]
For an ideal gas, the change in internal energy is given by:
\[
\Delta U = n C_v \Delta T
\]
where:
* n is the number of moles
* Cv is the molar heat capacity at constant volume
* ΔT is the change in temperature
The work done by the gas during an isobaric process is:
\[
W = n R \Delta T
\]
where:
* n is the number of moles
* R is the ideal gas constant
* ΔT is the change in temperature
**Relating Cp and Cv**
We are given Cp = (5/2)R. We know the relationship between Cp and Cv for an ideal gas is:
\[
C_p = C_v + R
\]
Therefore, we can find Cv:
\[
C_v = C_p - R = \frac{5}{2}R - R = \frac{3}{2}R
\]
**Calculating Heat (Q)**
Now, let's substitute the expressions for ΔU and W into the First Law of Thermodynamics:
\[
Q = \Delta U + W = (n C_v \Delta T) + (n R \Delta T)
\]
We can factor out nΔT:
\[
Q = n \Delta T (C_v + R)
\]
Since we know Cp = Cv + R, we can rewrite this as:
\[
Q = n \Delta T C_p
\]
Now, plug in the given values: n = 1 mol, ΔT = 40 K, and Cp = (5/2)R:
\[
Q = (1 \text{ mol}) (40 \text{ K}) \left(\frac{5}{2}R\right)
\]
\[
Q = 40 \cdot \frac{5}{2} R = 20 \cdot 5 R = 100 R
\]
**Oops!**
I made a mistake in my initial calculation. Let's re-examine the problem. The question asks for Q~p, which is the heat added during an isobaric process. We have:
\[
Q_p = n C_p \Delta T
\]
Plugging in the values:
\[
Q_p = (1 \text{ mol}) \left(\frac{5}{2}R\right) (40 \text{ K})
\]
\[
Q_p = \frac{5}{2} \cdot 40 \cdot R = 5 \cdot 20 \cdot R = 100R
\]
**Correcting the Answer**
My apologies for the initial error. The correct answer is **C) 100R**. I initially miscalculated the multiplication.
**Key Takeaways**
* Understand the First Law of Thermodynamics and its application to isobaric processes.
* Know the relationship between Cp, Cv, and R for ideal gases.
* Carefully substitute the given values into the appropriate equations.
* Double-check your calculations!
-
Q58.
Numerical: Same process: work W˜
A) nR?T
B) 0
C) nCv?T
D) nCp?T
Answer: A
-
Q59.
Numerical: A gas absorbs 1200 J while 300 J of work is done on it. ?U=
A) 900 J
B) 1500 J
C) -900 J
D) -1500 J
Answer: B
To determine the change in internal energy (\(\Delta U\)), we apply the First Law of Thermodynamics. This fundamental principle states that the internal energy of a system changes when energy is transferred into or out of the system in the form of heat and work.
1. Identify the Given Information:
Heat absorbed by the gas (\(Q\)) = 1200 J
Work done on the gas (\(W\)) = 300 J
2. Understand the Sign Convention:
In thermodynamics, when heat is absorbed by a system, \(Q\) is positive because energy is entering the system. Similarly, when work is done on the system (compression), the system gains energy, so \(W\) is also treated as a positive addition to the internal energy.
3. Apply the Formula:
The relationship is expressed as:
\[ \Delta U = Q + W \]
Substituting the values from the question:
\[ \Delta U = 1200 \text{ J} + 300 \text{ J} \]
\[ \Delta U = 1500 \text{ J} \]
Reasoning:
The gas is receiving energy from two different sources simultaneously. It gains 1200 J from the heat it absorbs and another 300 J from the work being performed on it. Since both actions increase the total energy stored within the gas, we add the two values together to find the total increase in internal energy.
The total change in internal energy is 1500 J because both the heat absorbed and the work done on the gas contribute to increasing its energy state.
-
Q60.
For cyclic process, net change in internal energy is
A) positive
B) negative
C) zero
D) infinite
Answer: C
-
Q61.
In a PV diagram, clockwise cycle area represents
A) work done on system
B) work done by system
C) zero work
D) heat lost
Answer: B
-
Q62.
For ideal gas, U depends only on
A) pressure
B) volume
C) temperature
D) density
Answer: C
-
Q63.
In adiabatic expansion of ideal gas, temperature
A) increases
B) decreases
C) remains same
D) oscillates
Answer: B
-
Q64.
For small temperature rise ?T, change in internal energy of n moles ideal gas is
A) nCv?T
B) nCp?T
C) nR?T lnV
D) zero
Answer: A
Okay, let's break down why option A, `nCv?T`, is the correct answer for the change in internal energy of *n* moles of an ideal gas with a small temperature rise ΔT.
Here's the reasoning, explained step-by-step:
**Understanding Internal Energy**
First, let's recall what internal energy (U) represents. For an ideal gas, internal energy is solely dependent on its temperature. It's the total energy associated with the random motion of the gas molecules. There are no intermolecular forces in an ideal gas, so no potential energy to consider.
**The Relationship Between Internal Energy, Temperature, and Moles**
The change in internal energy (ΔU) for an ideal gas is related to the number of moles (n), the specific heat at constant volume (Cv), and the change in temperature (ΔT) by the following equation:
\[
\Delta U = n C_v \Delta T
\]
**Explanation of the Terms**
* **n:** This is the number of moles of the gas. More moles mean more molecules, and therefore more energy.
* **Cv:** This is the molar specific heat at constant volume. It represents the amount of heat required to raise the temperature of one mole of the gas by one degree Celsius (or Kelvin) while keeping the volume constant. It's a property of the gas itself.
* **ΔT:** This is the change in temperature. A larger temperature change means a larger increase in the average kinetic energy of the molecules, and thus a larger change in internal energy.
**Why Other Options are Incorrect**
Let's look at why the other options are wrong:
* **B) nCp?T:** `Cp` (specific heat at constant pressure) is *not* the correct specific heat to use when calculating the change in internal energy. `Cp` accounts for the work done by the gas as it expands at constant pressure. The change in internal energy only depends on the temperature change at *constant volume*. The relationship is: `Cp = Cv + R`, where R is the ideal gas constant.
* **C) nR?T lnV:** This option relates the change in internal energy to the natural logarithm of volume (lnV). This is incorrect because the internal energy of an ideal gas *doesn't* depend on volume. This form is more related to the change in enthalpy.
* **D) zero:** The change in internal energy is clearly not zero if the temperature changes. Energy is added to the system to increase the temperature.
**The "Small Temperature Rise" Condition**
The question specifies a "small temperature rise." This is important because it implies that we can treat the gas as undergoing a quasi-static process, where the changes are gradual and reversible. This allows us to use the simple relationship `ΔU = nCvΔT` without needing to consider more complex thermodynamic relationships.
**In Conclusion**
Therefore, the correct answer is **A) nCv?T** because it accurately represents the change in internal energy of *n* moles of an ideal gas for a small temperature rise, based on the fundamental thermodynamic relationship.
-
Q65.
Joule showed that mechanical work can
A) create matter
B) be converted into heat quantitatively
C) not produce heat
D) violate energy conservation
Answer: B
-
Q66.
Joule's paddle-wheel experiment measured
A) R
B) J (Joule per calorie)
C) Cp
D) Cv
Answer: B
-
Q67.
Mechanical equivalent of heat J connects
A) Q (cal) to W (J)
B) mass to energy
C) entropy to temperature
D) pressure to volume
Answer: A
-
Q68.
1 cal of heat is equivalent to about
A) 4.2 J of work
B) 1 J of work
C) 42 J of work
D) 0.24 J of work
Answer: A
-
Q69.
If 6000 J of mechanical work is fully converted to heat, the heat in calories is about
A) 1430 cal
B) 6000 cal
C) 250 cal
D) 24,000 cal
Answer: A
-
Q70.
Numerical: Stirring 0.5 kg water (c=4200) raises its temperature by 2 K only by work. Required work˜
A) 4.2 kJ
B) 8.4 kJ
C) 2.1 kJ
D) 0.42 kJ
Answer: B
-
Q71.
Numerical: 200 cal corresponds approximately to
A) 84 J
B) 838 J
C) 4.2 kJ
D) 0.2 J
Answer: B
-
Q72.
Thermodynamics is the study of
A) chemical bonds only
B) heat, work, and the macroscopic states of systems
C) nuclear forces
D) optics
Answer: B
-
Q73.
Numerical: Work 1200 J done on an insulated system (Q=0). ?U equals
A) -1200 J
B) +1200 J
C) 0
D) +600 J
Answer: B
-
Q74.
Numerical: If 500 cal heat is supplied and 600 J work is done by system, ?U˜
A) 500 J
B) 2093 J
C) 1486 J
D) 600 J
Answer: B
-
Q75.
In a rigid container, adding heat primarily changes
A) pressure/temperature (internal energy)
B) volume (work)
C) mass
D) none
Answer: A
-
Q76.
A process with Q>0 and W<0 could be
A) heating with compression
B) cooling with expansion
C) adiabatic
D) isothermal with no work
Answer: A
-
Q77.
Temperature rise relates to internal energy increase because
A) molecules move faster on average
B) mass decreases
C) volume vanishes
D) pressure is zero
Answer: A
-
Q78.
Thermal equilibrium implies equality of
A) chemical potentials only
B) temperatures of systems
C) pressures of systems
D) volumes of systems
Answer: B
-
Q79.
At constant temperature, an ideal gas does work during expansion by drawing
A) heat from surroundings to keep T constant
B) no heat
C) internal energy increase
D) latent heat
Answer: A
-
Q80.
Numerical: 1.5 mol ideal gas undergoes ?T=25 K at constant V. Take R=8.31. ?U˜
A) 156 J
B) 467 J
C) 469 J (monoatomic: (3/2)nR?T)
D) 779 J
Answer: C
-
Q81.
Numerical: 0.25 kg water at 20°C mixed with 0.20 kg at 80°C. Final T (no loss)˜
A) 40°C
B) 47°C
C) 53°C
D) 60°C
Answer: B
-
Q82.
Numerical: 2.0 mol ideal diatomic gas (assume Cp=(7/2)R) heated isobarically by 30 K. Heat Q˜
A) 210R J
B) 105R J
C) 70R J
D) 35R J
Answer: A
-
Q83.
Numerical: Same as above, work W˜
A) nR?T = 60R J
B) 0
C) (5/2)nR?T
D) nCv?T
Answer: A
-
Q84.
Numerical: Gas expands at constant P from 0.010 to 0.030 m^3. P=1.5×10^5 Pa. Work˜
A) 1500 J
B) 3000 J
C) 4500 J
D) 6000 J
Answer: C
-
Q85.
Numerical: 300 g aluminum (900) at 100°C into 300 g water at 20°C. Final T˜
A) 50°C
B) 60°C
C) 70°C
D) 80°C
Answer: A
-
Q86.
Numerical: 1.0 mol ideal monoatomic gas expanded isothermally at 400 K from V to 3V. Work˜
A) nRT ln3
B) 3nRT
C) nCv?T
D) 0
Answer: A
-
Q87.
Numerical: If heat 1000 J is given to a rigid container gas (?V=0), and ?U=?
A) 0
B) 1000 J
C) -1000 J
D) 500 J
Answer: B
-
Q88.
Numerical: Steam at 100°C condenses to water at 100°C, releasing per kg
A) Lf
B) Lv
C) c?T
D) zero
Answer: B
The process described in the question is a phase change known as condensation. In this process, steam (a gas) at 100°C loses energy to become water (a liquid) at the same temperature.
During a phase change, the temperature of a substance remains constant even though energy is being transferred. This energy is referred to as latent heat. Latent heat is the energy required to change the state of a unit mass of a substance without changing its temperature.
There are two specific types of latent heat relevant to common phase changes:
1. Latent Heat of Fusion (\( L_f \)): This is the heat energy associated with the transition between the solid and liquid phases (such as ice melting or water freezing).
2. Latent Heat of Vaporization (\( L_v \)): This is the heat energy associated with the transition between the liquid and gaseous phases (such as water boiling or steam condensing).
The formula for the total heat (\( Q \)) released or absorbed during a phase change is:
\[ Q = m \cdot L \]
In this case, because the transition is between steam and water, we use the latent heat of vaporization (\( L_v \)). Since the question asks for the energy released per kg, we assume the mass (\( m \)) is 1 kg. Therefore:
\[ Q = 1 \text{ kg} \cdot L_v = L_v \]
Option C, \( c\Delta T \), represents sensible heat, which is the energy required to change the temperature of a substance. Because the temperature remains constant at 100°C in this scenario, \( \Delta T \) is zero, making this formula inapplicable for the phase change itself.
The energy released when 1 kg of steam condenses into water at a constant temperature of 100°C is equal to the latent heat of vaporization (\( L_v \)).
-
Q89.
Numerical: 50 g steam at 100°C condenses (Lv=2.26 MJ/kg). Heat released˜
A) 1.13×10^5 J
B) 2.26×10^5 J
C) 1.13×10^4 J
D) 2.26×10^4 J
Answer: A
To calculate the heat released during the condensation of steam, we must use the principle of latent heat. Latent heat is the energy released or absorbed by a substance during a change in its physical state (such as gas to liquid) that occurs without a change in temperature.
1. Identify the Given Information:
Mass of steam (\( m \)) = 50 g
Latent heat of vaporization (\( L_v \)) = 2.26 MJ/kg
2. Convert Units to the Standard International (SI) System:
Before performing the calculation, it is necessary to ensure the units are consistent. We convert the mass from grams to kilograms and the latent heat from Megajoules to Joules:
Mass: \( m = \frac{50}{1000} = 0.05 \text{ kg} \)
Latent Heat: \( L_v = 2.26 \times 10^6 \text{ J/kg} \)
3. Apply the Latent Heat Formula:
The formula for the total heat (\( Q \)) released during a phase change is:
\[ Q = m \times L_v \]
Substituting the known values into the equation:
\[ Q = 0.05 \text{ kg} \times (2.26 \times 10^6 \text{ J/kg}) \]
\[ Q = 0.113 \times 10^6 \text{ J} \]
To express this in standard scientific notation, we move the decimal point one place to the right:
\[ Q = 1.13 \times 10^5 \text{ J} \]
This result matches Option A.
By converting the mass to kilograms and multiplying by the latent heat of vaporization, we determine that the total heat released during condensation is \( 1.13 \times 10^5 \text{ J} \).
-
Q90.
Numerical: Compressing a gas adiabatically does
A) decreases its T
B) increases its T
C) leaves T same
D) random
Answer: B
-
Q91.
Numerical: 0.10 kg ice at 0°C into 0.30 kg water at 20°C. Will all ice melt? (Lf=334 kJ/kg, c=4200)
A) Yes; final ~?°C
B) No; some ice left
C) Temperature rises
D) None
Answer: B
-
Q92.
Numerical: Gas absorbs 800 J; ?U=200 J. Work by gas=
A) 600 J
B) 1000 J
C) 200 J
D) -600 J
Answer: A
-
Q93.
Numerical: For ideal monoatomic gas, Cv=(3/2)R. For 3 mol and ?T=10 K, ?U˜
A) 45R J
B) 30R J
C) 15R J
D) 3R J
Answer: A
-
Q94.
Numerical: A 60 W immersion heater runs 5 min in 0.50 kg water. ?T˜
A) 3.6 K
B) 6.0 K
C) 8.6 K
D) 10.0 K
Answer: A
-
Q95.
Numerical: A gas expands from 1 L to 4 L at constant P=2×10^5 Pa. Work˜
A) 300 J
B) 600 J
C) 1000 J
D) 6000 J
Answer: B
-
Q96.
Numerical: If 2500 J work is done on an adiabatic system, its internal energy
A) decreases by 2500 J
B) increases by 2500 J
C) unchanged
D) random
Answer: B
-
Q97.
Numerical: Calorimeter of water equivalent 100 g is at 20°C. 200 g water at 80°C is mixed; final T˜
A) 40°C
B) 50°C
C) 60°C
D) 70°C
Answer: B
-
Q98.
Numerical: Convert 500 cal to joules (J˜4.186).
A) 1190 J
B) 1674 J
C) 2093 J
D) 2500 J
Answer: C
-
Q99.
Numerical: 2 mol ideal monoatomic gas expanded at constant P from 300 K to 360 K. Work˜
A) nR?T = 2×8.31×60 J
B) (3/2)nR?T
C) 0
D) nCp?T
Answer: A
-
Q100.
The SI unit of electric charge is
A) Coulomb
B) Ampere
C) Volt
D) Ohm
Answer: A
-
Q101.
The charge on an electron is
A) 1.6×10\(^{-19}\) C
B) 1.6×10\(^{-20}\) C
C) 1.6×10\(^{-21}\) C
D) 1.6×10\(^{-22}\) C
Answer: A
-
Q102.
The law of conservation of charge states that
A) Charge can be created
B) Charge can be destroyed
C) Charge can be transferred
D) The total charge in an isolated system remains constant
Answer: D
-
Q103.
Coulomb’s law states that the force between two point charges is
A) Directly proportional to the product of charges
B) Inversely proportional to the square of the distance
C) Both A and B
D) Neither A nor B
Answer: C
-
Q104.
The value of Coulomb’s constant k is
A) 9×10\(^{9}\) N m\(^2\)/C\(^2\)
B) 9×10\(^{-9}\) N m\(^2\)/C\(^2\)
C) 9×10\(^{9}\) N m\(^2\)/C\(^2\)
D) 9×10\(^{-9}\) N m\(^2\)/C\(^2\)
Answer: A
-
Q105.
The electric field intensity is defined as
A) Force per unit charge
B) Force per unit mass
C) Work per unit charge
D) Energy per unit charge
Answer: A
-
Q106.
The SI unit of electric field intensity is
A) N/C
B) V/m
C) Both A and B
D) Neither A nor B
Answer: C
-
Q107.
The electric field due to a point charge q at a distance r is
A) \( k q / r \)
B) \( k q / r^2 \)
C) \( k q / r^3 \)
D) \( k q r \)
Answer: B
-
Q108.
The electric field lines due to a positive point charge are
A) Radially inward
B) Radially outward
C) Parallel
D) Perpendicular
Answer: B
-
Q109.
The electric field lines due to a negative point charge are
A) Radially inward
B) Radially outward
C) Parallel
D) Perpendicular
Answer: A
-
Q110.
The electric potential at a point is defined as
A) Work done per unit charge
B) Force per unit charge
C) Energy per unit charge
D) Both A and C
Answer: D
-
Q111.
The SI unit of electric potential is
A) Volt
B) Joule/Coulomb
C) Both A and B
D) Neither A nor B
Answer: C
-
Q112.
The electric potential due to a point charge q at a distance r is
A) \( k q / r \)
B) \( k q / r^2 \)
C) \( k q / r^3 \)
D) \( k q r \)
Answer: A
-
Q113.
The electric potential difference between two points is
A) Work done per unit charge
B) Force per unit charge
C) Energy per unit charge
D) Both A and C
Answer: D
-
Q114.
The SI unit of electric potential difference is
A) Volt
B) Joule/Coulomb
C) Both A and B
D) Neither A nor B
Answer: A
-
Q115.
The capacitance of a capacitor is defined as
A) Charge per unit voltage
B) Voltage per unit charge
C) Charge per unit energy
D) Energy per unit charge
Answer: A
-
Q116.
The SI unit of capacitance is
A) Farad
B) Coulomb/Volt
C) Both A and B
D) Neither A nor B
Answer: C
-
Q117.
The capacitance of a parallel plate capacitor is
A) \( \epsilon_0 A / d \)
B) \( \epsilon_0 d / A \)
C) \( A \epsilon_0 / d \)
D) \( d / \epsilon_0 A \)
Answer: A
-
Q118.
If the area of the plates of a parallel plate capacitor is doubled, the capacitance becomes
A) Half
B) Double
C) One-fourth
D) Four times
Answer: B
-
Q119.
If the distance between the plates of a parallel plate capacitor is doubled, the capacitance becomes
A) Half
B) Double
C) One-fourth
D) Four times
Answer: A
-
Q120.
The energy stored in a capacitor is
A) \( \frac{1}{2} C V^2 \)
B) \( \frac{1}{2} Q V \)
C) \( \frac{1}{2} Q^2 / C \)
D) All of these
Answer: D
-
Q121.
If the charge on a capacitor is doubled, the energy stored becomes
A) Half
B) Double
C) One-fourth
D) Four times
Answer: B
-
Q122.
If the voltage across a capacitor is doubled, the energy stored becomes
A) Half
B) Double
C) One-fourth
D) Four times
Answer: B
-
Q123.
The dielectric constant of a medium is
A) \( \frac{C}{C_0} \)
B) \( \frac{C_0}{C} \)
C) \( \epsilon / \epsilon_0 \)
D) Both A and C
Answer: D
-
Q124.
The dielectric constant of vacuum is
A) 1
B) 0
C) 8
D) -1
Answer: A
-
Q125.
The dielectric constant of air is approximately
A) 1
B) 1.0006
C) 2
D) 3
Answer: B
-
Q126.
The dielectric constant of water is about
A) 80
B) 60
C) 40
D) 20
Answer: A
-
Q127.
The dielectric constant of mica is about
A) 3
B) 5
C) 7
D) 9
Answer: C
-
Q128.
Gauss’s law states that the electric flux through a closed surface is equal to
A) \( \frac{1}{\epsilon_0} \) times the charge enclosed
B) \( \epsilon_0 \) times the charge enclosed
C) \( \frac{1}{\epsilon_0} \) times the total charge
D) \( \epsilon_0 \) times the total charge
Answer: B
-
Q129.
The electric flux through a closed surface is zero if
A) No charge is enclosed
B) The net charge enclosed is zero
C) Both A and B
D) Neither A nor B
Answer: C
-
Q130.
The electric field due to an infinite plane sheet of charge is
A) \( \sigma / 2 \epsilon_0 \)
B) \( \sigma / \epsilon_0 \)
C) \( 2 \sigma / \epsilon_0 \)
D) \( \sigma / 4 \epsilon_0 \)
Answer: B
To find the electric field produced by an infinite plane sheet of charge, we utilize Gauss's Law, which states that the total electric flux through a closed surface is proportional to the net charge enclosed within that surface.
In the context of a conducting infinite plane sheet, the charge resides on the surface. To calculate the field, we imagine a Gaussian surface in the shape of a small cylinder (often called a pillbox) that cuts through the surface of the sheet. For a conductor in electrostatic equilibrium, the electric field inside the material is zero. Consequently, the electric flux exists only through the end of the cylinder that is outside the sheet.
The total electric flux \( \Phi \) through this Gaussian surface is:
\[ \Phi = E \cdot A \]
where \( E \) is the electric field strength and \( A \) is the area of the cylinder's face.
According to Gauss's Law, this flux is equal to the enclosed charge \( q \) divided by the permittivity of free space \( \epsilon_0 \):
\[ \Phi = \frac{q}{\epsilon_0} \]
The surface charge density \( \sigma \) is defined as the charge per unit area (\( \sigma = q / A \)), so the enclosed charge can be expressed as:
\[ q = \sigma \cdot A \]
Substituting this into the Gauss's Law formula gives:
\[ E \cdot A = \frac{\sigma \cdot A}{\epsilon_0} \]
By dividing both sides by the area \( A \), we find the expression for the electric field:
\[ E = \frac{\sigma}{\epsilon_0} \]
While a single non-conducting thin sheet has a field of \( \sigma / 2\epsilon_0 \), the field near a conducting plate or a sheet where the charge is considered on the surface is \( \sigma / \epsilon_0 \).
Summary: The electric field due to an infinite charged sheet (specifically a conducting one) is given by the formula \( \sigma / \epsilon_0 \).
-
Q131.
The electric field due to an infinite line charge is
A) \( \lambda / 2 \pi \epsilon_0 r \)
B) \( \lambda / 4 \pi \epsilon_0 r \)
C) \( 2 \lambda / \pi \epsilon_0 r \)
D) \( \lambda \pi \epsilon_0 r \)
Answer: A
-
Q132.
The electric field inside a conductor is
A) Zero
B) Constant
C) Proportional to distance
D) Inversely proportional to distance
Answer: A
-
Q133.
The electric potential inside a conductor is
A) Zero
B) Constant
C) Proportional to distance
D) Inversely proportional to distance
Answer: B
-
Q134.
The charge on a conductor resides
A) Inside the conductor
B) On the surface
C) Both inside and on the surface
D) Neither inside nor on the surface
Answer: B
-
Q135.
The electric field at the surface of a conductor is
A) Zero
B) \( \sigma / \epsilon_0 \)
C) \( 2 \sigma / \epsilon_0 \)
D) \( \sigma / 4 \epsilon_0 \)
Answer: B
-
Q136.
The capacitance of a spherical capacitor is
A) \( 4 \pi \epsilon_0 a b / (b - a) \)
B) \( 4 \pi \epsilon_0 (b - a) \)
C) \( 4 \pi \epsilon_0 / (b - a) \)
D) \( 4 \pi \epsilon_0 a / (b - a) \)
Answer: A
-
Q137.
The capacitance of an isolated sphere of radius R is
A) \( 4 \pi \epsilon_0 R \)
B) \( 4 \pi \epsilon_0 R^2 \)
C) \( R / (4 \pi \epsilon_0) \)
D) \( 4 \pi \epsilon_0 / R \)
Answer: D
-
Q138.
The equivalent capacitance of two capacitors in series is
A) \( C_1 + C_2 \)
B) \( \frac{C_1 C_2}{C_1 + C_2} \)
C) \( C_1 C_2 \)
D) \( C_1 - C_2 \)
Answer: B
-
Q139.
The equivalent capacitance of two capacitors in parallel is
A) \( C_1 + C_2 \)
B) \( \frac{C_1 C_2}{C_1 + C_2} \)
C) \( C_1 C_2 \)
D) \( C_1 - C_2 \)
Answer: A
-
Q140.
If two capacitors of capacitance C each are connected in series, the equivalent capacitance is
A) C
B) 2C
C) C/2
D) 4C
Answer: C
-
Q141.
If two capacitors of capacitance C each are connected in parallel, the equivalent capacitance is
A) C
B) 2C
C) C/2
D) 4C
Answer: B
-
Q142.
The energy density in an electric field is
A) \( \frac{1}{2} \epsilon_0 E^2 \)
B) \( \frac{1}{2} \epsilon_0 E \)
C) \( \epsilon_0 E^2 \)
D) \( \epsilon_0 E \)
Answer: A
-
Q143.
The force between two charges is F. If the distance between them is doubled, the force becomes
A) F/2
B) F/4
C) 2F
D) 4F
Answer: B
-
Q144.
The force between two charges is F. If the magnitude of each charge is doubled, the force becomes
A) F/2
B) F/4
C) 2F
D) 4F
Answer: D
-
Q145.
The electric potential at a point due to a point charge is V. If the distance is doubled, the potential becomes
A) V/2
B) V/4
C) 2V
D) 4V
Answer: B
-
Q146.
The electric field at a point due to a point charge is E. If the distance is doubled, the field becomes
A) E/2
B) E/4
C) 2E
D) 4E
Answer: B
-
Q147.
The work done in moving a charge between two points in an electric field is independent of the path taken. This is because the electric field is
A) Conservative
B) Non-conservative
C) Uniform
D) Non-uniform
Answer: A
-
Q148.
The electric field and electric potential are related by
A) \( E = - dV / dr \)
B) \( V = - dE / dr \)
C) \( E = dV / dr \)
D) \( V = dE / dr \)
Answer: A
-
Q149.
The potential difference between two points in a uniform electric field E separated by a distance d is
A) Ed
B) E/d
C) E\(^2\) d
D) E/d\(^2\)
Answer: A